Champion usn-72 ユーザーガイド
7
Part 2: INSTALLATION
2.3 Reassembly
Special Tools and Materials Required—
• Bubble level (3 ft.)
• Silicone sealant, (1) 12 fl. ounce tube, Dow Corning® RTV or comparable
• Plumber's sealing putty (Champion P/N 104889) or comparable
• Pipe thread sealant, Loctite® 565 or comparable
If you disassembled your dishwasher to move it through hatches as described in Part 2.2, then
• Bubble level (3 ft.)
• Silicone sealant, (1) 12 fl. ounce tube, Dow Corning® RTV or comparable
• Plumber's sealing putty (Champion P/N 104889) or comparable
• Pipe thread sealant, Loctite® 565 or comparable
If you disassembled your dishwasher to move it through hatches as described in Part 2.2, then
follow the instructions in this part to reassemble your dishwasher. Go to Part 2.4, Permanent
Placement, if disassembly was not required for your dishwasher.
Perform the following steps to reassemble the dishwasher prior to permanent placement.
Refer to Fig. 2.1 on the preceding page.
1. Before moving the sections into position, inspect the location site to ensure the electrical,
plumbing, and ventilation services are provided in the correct locations. Compare the site
connections with the dishwasher to ensure they will match when the machine is set in its
permanent location.
2. Move the wash and rinse tanks in close proximity to each other in the direction
they will be installed.
3. Apply a 1/2" bead of silicone sealant on the face of all sides of the wash tank hood gasket.
4. Move the rinse tank closer to the wash tank and check the alignment of the bolt holes at the base
4. Move the rinse tank closer to the wash tank and check the alignment of the bolt holes at the base
and around the tank hood.
5. Adjust the rinse tank adjustable legs to align the bolt holes.
6. BOLT THE HOOD SECTIONS FIRST.
Make sure the U-clip removed in Step 8, Part 2.2 is installed.
Start the bolts and tighten nuts hand tight.
7. Check the alignment of the 1-1/2" drain union underneath the machine. Adjust tanks as required.
8. Start the bolts and hand tighten the nuts to join the bases.
9. Connect the 1-1/2" drain union.
8. Start the bolts and hand tighten the nuts to join the bases.
9. Connect the 1-1/2" drain union.
10. Tighten all bolts securely using a cross pattern to pull the tanks together evenly.
11. Reconnect the wiring and plumbing. Refer to Steps 12-14, Part 2.2 and Fig 2.1.
12. Pull the conveyor drive chains stored in the wash tank back to the rinse tank. Make sure
the drive chain with the dishrack lugs is positioned on the rear track. See Item 7, Fig.2.1.
13. Replace the drive chain master links and tighten the chain adjusters evenly. Proper chain tension
is achieved when the chain can be lifted off the track a maximum of 1-1/2".
14. Reinstall remaining plumbing using plumber's putty or thread sealant where required.
Refer to Steps 2-5, Part 2.2 and Fig.2.1
15. Position dishwasher in its permanent location.
16. Lift the dishwasher and replace the adjustable legs with the flanged mounting feet provided.
17. Level the dishwasher front to back and side to side by turning the adjustable feet.
16. Lift the dishwasher and replace the adjustable legs with the flanged mounting feet provided.
17. Level the dishwasher front to back and side to side by turning the adjustable feet.
Make sure the load and unload openings align with the table system height.
18. Reinstall the vent collars.
19. Go to Part 2.4, Permanent Placement.
19. Go to Part 2.4, Permanent Placement.