Roland GW-8 ユーザーガイド
20
Keyboard Mode Functions
The GW-8 contains more than 1000 different Tones. You can
use these Tones in the three keyboard modes (Single, Split,
Dual).
use these Tones in the three keyboard modes (Single, Split,
Dual).
In Split mode or Dual mode, you can use the cursor buttons to
move the cursor to the Tone number of the Upper Tone or
Lower Tone, and select a different Tone for each.
move the cursor to the Tone number of the Upper Tone or
Lower Tone, and select a different Tone for each.
Using the VALUE dial
1.
Press [TONE] so the button is lit.
Alternatively, use the cursor buttons in the Main screen to
move the cursor to the Tone number.
move the cursor to the Tone number.
2.
Turn the VALUE dial to step through the Tones one by one.
Alternatively, you can press one of the TONE SELECT
buttons ([PIANO]–[SPECIAL]) to select a Tone by
category.
buttons ([PIANO]–[SPECIAL]) to select a Tone by
category.
When the cursor in the screen is at the Tone number, you can
also select a Tone by turning [NUMERIC] on, using the TONE
SELECT buttons to enter a Tone number, and then pressing
[ENTER].
also select a Tone by turning [NUMERIC] on, using the TONE
SELECT buttons to enter a Tone number, and then pressing
[ENTER].
Choosing from the Tone list
1.
In the Main screen, use the cursor buttons to move the
cursor to the Tone number.
2.
Press [ENTER].
3.
Use [
] [
] or the VALUE dial to select a Tone.
You can press one of the TONE SELECT buttons
([PIANO]–[SPECIAL]) to select a Tone by category.
([PIANO]–[SPECIAL]) to select a Tone by category.
4.
Press [ENTER] to set the Tone.
If you press [EXIT] without pressing [ENTER], the list will
close without the currently selected Tone being changed.
close without the currently selected Tone being changed.
You can use [
] [
] to select a sub-category within the
currently selected category.
You can edit the currently selected Tone and store it in the
Performance. For details, refer to “Editing a Tone” (p. 40).
Performance. For details, refer to “Editing a Tone” (p. 40).
The Favorite function lets you register frequently used Tones or
Performances at
Performances at
TONE SELECT buttons
(
[0]–[9]
) so that they can
be called up easily.
At each of the ten buttons you can register ten Tones or
Performances.
Performances.
When you turn
FAVORITE [BANK]
on, the ten
TONE SELECT
buttons
are used to specify the bank, allowing you to switch
between the ten banks. This allows you to register a total of
one hundred Favorite Tones or Performances (ten banks of
ten).
one hundred Favorite Tones or Performances (ten banks of
ten).
After selecting a Tone or a Performance, hold down
FAVORITE
[ON/OFF]
and press one of
[0]–[9]
in which you want to
register that Tone or Performance.
Press
FAVORITE [ON/OFF]
so the button is lit, and press one of
[0]–[9]
in which you registered the desired Tone or
Performance.
If you press
FAVORITE [BANK]
so it’s lit, one of the
[0]–[9]
buttons corresponding to the currently selected bank will blink.
To change the bank, press the button of the desired bank (
To change the bank, press the button of the desired bank (
[0]–
[9
]) while
FAVORITE [BANK]
is lit.
Selecting a Tone ([TONE])
Registering Frequently Used
Tones or Performances in a
Button (FAVORITE Buttons)
Tones or Performances in a
Button (FAVORITE Buttons)
Registering a Favorite Tone/Performance
Selecting a Favorite Tone/Performance
Checking or Changing the Registered
Bank
Bank
GW-8_e.book 20 ページ ２００８年７月３０日 水曜日 午後２時４分