Roland juno-stage ユーザーガイド
115
Chapter 8. Detailed Editing for Patches
STEP LFO
Parameters indicated by (
OUTPUT
For details regarding effect settings, refer to the pages shown below.
Parameter
Value
Explanation
Step Type
Step Type
TYP1, TYP2
When generating an LFO waveform from the data specified in LFO Step 1–16, specify whether the level
will change abruptly at each step or will be connected linearly.
will change abruptly at each step or will be connected linearly.
TYP1:
stair-step change
TYP2:
linear change
Step 1–16
Step 1–16
-36–+36
Specifies the data for the Step LFO.
If the LFO Pitch Depth is +63, each +1 unit of the step data corresponds to a pitch of +50 cents.
Parameter
Value
Explanation
Patch Out Assign
MFX,
L+R,
L, R,
TONE
L+R,
L, R,
TONE
Specifies how the direct sound of each patch will be output.
MFX:
Output in stereo through multi-effects. You can also apply chorus or reverb to the sound that passes
through multi-effects.
L+R:
Output in stereo to the OUTPUT jacks without passing through the multi-effect
L:
Output in mono to the OUTPUT L jack without passing through the multi-effect
R:
Output in mono to the OUTPUT R jack without passing through the multi-effect
TONE:
Outputs according to the settings for each tone.
Tone Out Assign
MFX,
L+R,
L, R
L+R,
L, R
Specifies how the direct sound of each tone will be output.
MFX:
Output in stereo through multi-effects. You can also apply chorus or reverb to the sound that passes
through multi-effects.
L+R:
Output in stereo to the OUTPUT jacks without passing through the multi-effect
L:
Output in mono to the OUTPUT L jack without passing through the multi-effect
R:
Output in mono to the OUTPUT R jack without passing through the multi-effect
* If the Patch Out Assign is set to anything other than “TONE,” these settings will be ignored.
* If “Struct 1 & 2, 3 & 4” (p. 99) is set to TYPE 02–10, the settings for tone 1 (3) will follow the settings
* If “Struct 1 & 2, 3 & 4” (p. 99) is set to TYPE 02–10, the settings for tone 1 (3) will follow the settings
of tone 2 (4). (This is because the outputs of tones 1 and 2 are combined into tone 2, and the outputs
of tones 3 and 4 are combined into tone 4.)
of tones 3 and 4 are combined into tone 4.)
* Sounds are output to chorus and reverb in mono at all times.
* The output destination of the signal after passing through the chorus is set with the Chorus Output Select.
* The output destination of the signal after passing through the chorus is set with the Chorus Output Select.
Tone Out Level
0–127
Level of the signal that is sent to the output destination specified by Tone Output Assign
Send Level (Output = MFX)
Tone Chorus Send
0–127
Level of the signal sent to chorus for each tone if the tone is sent through MFX
Tone Reverb Send
0–127
Level of the signal sent to reverb for each tone if the tone is sent through MFX
Send Level (Output = non MFX)
Tone Chorus Send
0–127
Level of the signal sent to chorus for each tone if the tone is not sent through MFX
Tone Reverb Send
0–127
Level of the signal sent to reverb for each tone if the tone is not sent through MFX
Setting Effects for a Patch (Effects/MFX/MFX Control/Chorus/Reverb)
ZOOM
ZOOM
ZOOM
JUNO-STAGE_e.book 115 ページ ２００８年１０月１７日 金曜日 午後１２時２７分