Roland RS-70 オーナーマニュアル
85
Using the sequencer to create patterns (Pattern mode)
Pattern Mode
Meas (Measure)
Sets the range of measures you wish to copy.
VALUE
Meas:
Specifies the measure at which copying is to begin. If
you select “SETUP,” the copy will start from the first
measure, including the
you select “SETUP,” the copy will start from the first
measure, including the
pattern setup data
.
for:
Specifies the number of measures to be copied. If
you select “ALL,” data from the measure you
specified for
you select “ALL,” data from the measure you
specified for
Meas
to the last measure of the pattern
will be copied.
Event
Specifies the type of music data you wish to copy.
VALUE
ALL:
All music data
NOTE:
Note (C-1–G 9)
Specify the range of notes. You can also press keys
on the keyboard to specify the range.
on the keyboard to specify the range.
P.AFT:
Polyphonic Aftertouch
C.C.:
Controller numbers (0–127)
PROG:
Program numbers (1–128)
C.AFT:
Channel Aftertouch
BEND:
Pitch Bend
SYS-EX:
System Exclusive
TUNE:
Tune Request
To Meas
Specifies the copy-start measure of the copy-destination part.
Value:
SETUP, 001–998
If you select “SETUP” for
Meas
, this value will be fixed at “SETUP.”
Mode
Specifies the copy mode.
VALUE
REPLACE:
Music data in the copy destination will be erased
(i.e., overwritten) when the copy takes place.
(i.e., overwritten) when the copy takes place.
MIX:
Music data in the copy destination will be combined
with the newly copied data.
with the newly copied data.
Times
Sets the number of times that the data will be copied.
Value:
1–998
Inserting blank measures
(PTN INSERT)
This operation inserts blank measures into the specified location of a
pattern. If you wish to add more musical material in the middle of a
pattern, use this operation to insert blank measures before recording
the additional material. The inserted measures will have the same
time signature as the pattern.
pattern. If you wish to add more musical material in the middle of a
pattern, use this operation to insert blank measures before recording
the additional material. The inserted measures will have the same
time signature as the pattern.
fig.r06-60_40
Meas (Measure)
Sets the range of blank measures that will be inserted.
VALUE
Meas:
Specifies the measure at which the blank measures
will be inserted.
will be inserted.
for:
Specifies the number of measures to be inserted.
Transposing the pitch (PTN TRANSPOSE)
This operation shifts the note numbers (pitch) of each part in a
pattern.
pattern.
fig.r06-60a
Part
Specifies the part(s) that you wish to transpose.
If you choose “ALL,” all parts will be specified.
Value:
ALL, 1–16
You can also select the part by pressing [0]–[9] or by holding
down [SHIFT] and pressing [1]–[6].
down [SHIFT] and pressing [1]–[6].
Meas (Measure)
Sets the range of measures that will be transposed.
VALUE
Meas:
Specifies the measure at which transposition is to begin.
for:
Specifies the number of measures to be transposed.
If you select “ALL,” data from the measure you
specified for
If you select “ALL,” data from the measure you
specified for
Meas
to the last measure of the pattern
will be transposed.
About pattern setup
If you select SETUP as the beginning of the copy region, the
following settings will be copied together with the sequence
data. This data is collectively known as pattern setup data.
following settings will be copied together with the sequence
data. This data is collectively known as pattern setup data.
• Pattern name
• Voice reserve settings
• Pattern level
• MFX Source
• MFX settings
• Chorus settings
• Reverb settings
• Part level*
• Part pan*
• Receive channel*
• Receive switch*
• Receive program change*
• Receive bank select*
• Scale tune*
• Patches*
* The asterisk indicates parameters that are set independently for
each part.
RS-70_e4.book 85 ページ ２００３年８月１８日 月曜日 午前９時４７分