Enterasys rbt-8100 仕様ガイド
Specifications
The physical specifications for the RBT‐8100 Wireless Switch are
listed in
listed in
.
Ensure that the environmental requirements are within the ranges
described in
described in
.
Chassis and Software Installation Information
This document is only intended as a quick start. Refer to the
RoamAbout RBT‐8100 Wireless Switch Installation Guide for
hardware (specifications, regulatory) and software installation
information.
RoamAbout RBT‐8100 Wireless Switch Installation Guide for
hardware (specifications, regulatory) and software installation
information.
The latest RoamAbout documentation is available from
Electrical Hazard: Only qualified personnel should
perform installation procedures.
perform installation procedures.
Table 1 Physical Specifications
Parameter
Width
Height
Depth
Approximate
Specification
Specification
430 mm
(16.93 in.)
87.5 mm
(3.445 in.)
672 mm
(26.457 in.)
Table 2 Environmental Specifications
Parameter
Description
Operating Temp.
10°C to 35°C (50°F to 95°F) with the maximum
rate of change not to exceed 10°C per hour
rate of change not to exceed 10°C per hour
Non-Operating Temp.
40°C to +70°C (104°F to 158°F)
Altitude
-60 meters (-197 feet) below sea level to 4000
meters (13,123 feet) above sea level
meters (13,123 feet) above sea level
Non-Operating Humidity 90%, non-condensing @ 35°C (95°F)
Acoustic noise
Sound Pressure: 55 dBA (Rackmount) in an idle
state at typical office ambient temperature (23
+/- degrees C)
Sound Power: 7.0 BA in an idle state at typical
office ambient temperature (23 +/- 2 degrees C)
state at typical office ambient temperature (23
+/- degrees C)
Sound Power: 7.0 BA in an idle state at typical
office ambient temperature (23 +/- 2 degrees C)
Operating Shock
No errors with a half sine wave shock of 2G
(with 11 millisecond duration)
(with 11 millisecond duration)
Package Shock
Operational after a 24-inch free fall, although
cosmetic damage may be present (Chassis
Weight 40–80 lbs)
cosmetic damage may be present (Chassis
Weight 40–80 lbs)
ESD
+/-15kV per Intel Environmental test
specification
specification
System Cooling
Requirement in BTU/Hr
Requirement in BTU/Hr
1826 BTU/hour
Connecting the Cables
button. Refer to the RoamAbout RBT‐8100 Wireless Switch
Installation Guide for additional instructions on setup.
Installation Guide for additional instructions on setup.
Figure 1 Back I/O Ports and Features
Front Panel Controls and Indicators
Front panel LED indicators and their descriptions are shown in
Figure 2 Front Panel Indicators
Mounting in a Four-Post System
The bracket kit allows you to install the RBT‐8100 Wireless Switch
into most four‐post rack and cabinet systems. The only tool
required is a Phillips screwdriver.
into most four‐post rack and cabinet systems. The only tool
required is a Phillips screwdriver.
For instructions on mid‐mounting in a two‐post rack system, refer
to the RoamAbout RBT‐8100 Wireless Switch Installation Guide.
to the RoamAbout RBT‐8100 Wireless Switch Installation Guide.
1. Attach the chassis brackets to the chassis as in
.
Caution: Changes or modifications made to this device which are
not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Caution: Ensure that you wear the ESD (Electrical Static
Discharge) strap during the installation.
Discharge) strap during the installation.
A
B
D E
F
G
H
C
I
A. AC power connector
B. (Not supported)
C. (Not supported)
D. (Not supported)
E. Serial port A
B. (Not supported)
C. (Not supported)
D. (Not supported)
E. Serial port A
F. (Not supported)
G. NIC 1 connector (1 Gbit)
H. NIC 2 connector (10/100 Mbit)
I. PCI card bracket (full height)
G. NIC 1 connector (1 Gbit)
H. NIC 2 connector (10/100 Mbit)
I. PCI card bracket (full height)
1
2
B
C
D
E
A
A. Power button and power
LED
B. Network activity LEDs
(NIC 1, NIC 2)
C. System fault LED
D. Hard drive activity LED
E. Reset button
D. Hard drive activity LED
E. Reset button
Figure 3 Installing Bracket in Front-Mount Position
2. Attach disks to chassis as shown in
.
Figure 4 Attaching Disk to Chassis
Figure 5 Attaching Rear Bracket to Rear Post
4. Install the chassis in rack as shown in
.
D
B
C
A
A. Chassis bracket in front mount position
B. Bracket holes
C. Chassis tabs
D. #6-32 x 3/16-inch screw
A
B
A. Chassis disk
B. #6-32 x 3/16-inch screw
B. #6-32 x 3/16-inch screw
B
C
A
A. #10-32 x 1/2-inch screw
B. Nut bar
C. Rear bracket
B. Nut bar
C. Rear bracket
Figure 6 Installing Chassis in Rear Brackets
5. Attach the chassis brackets to the front posts as shown in
.
Figure 7 Attaching Front Bracket to Front Post
Initial Configuration
Once your RBT‐8100 is physically installed, you can configure it
quickly using the quickstart command, which runs an interactive
script that prompts you for required information and lists the
default if applicable. Refer to the RoamAbout RBT‐8100 Wireless
Switch Installation Guide for information about other initialization
options.
quickly using the quickstart command, which runs an interactive
script that prompts you for required information and lists the
default if applicable. Refer to the RoamAbout RBT‐8100 Wireless
Switch Installation Guide for information about other initialization
options.
B
A
A.Chassis disk
B.Rear bracket
B.Rear bracket
A
C
B
A. Front post
B. Screw
C. Spacer
B. Screw
C. Spacer
17x8.5 with bleed