Marantz SR4023 ユーザーガイド

ENGLISH

With this unit you can preset up to 50 FM/AM stations 
in any order.
For each station, you can memorize the frequency 
and reception mode if desired.

This function automatically scans the FM and AM 
band and enters all stations with proper signal 
strength into the memory.

  To select FM, press the BAND button on the 

front panel.

  While pressing the MEMO button, press the 

3

 button.

 

  “AUTO PRESET” will appear on the display, 

and scanning starts from the lowest frequency.

  Each time the tuner fi nds a station, scanning 

will pause and the station will be played for fi ve 
seconds.

 

  During this time, the following operations are 

possible.

 

  The band can be changed by the BAND button.

  If no button is pressed during this period, the 

current station is memorized in location Preset 
01. 

 

  If you wish to skip the current station, press the 

3

 cursor button during this period, this station 

is skipped and auto presetting continues.

  Operation stops automatically when all 50 

preset memory positions are fi lled or when auto 
scanning attains the highest end of all bands. 
If you desire to stop the auto preset memory at 
anytime, press the CLEAR button.

It is possible that existing preset memory positions 
will be overwritten.

  Tune into the radio station you desire (Refer to 

the “MANUAL TUNING” or “AUTO TUNING” 
section).

 Press 

the 

MEMORY button on the front panel. 

“– –“ (preset number) starts blinking on the 
display.

  Select the preset number by pressing the 

TUNING 

3

 or 

4

 buttons, while this indicator is 

still blinking (approx. 5 seconds)

 Press 

the 

MEMORY button again to enter. The 

display stops blinking. 

 

  The station is now stored in the specified 

preset memory location.

  Tune into the radio station you desire (Refer to 

the “MANUAL TUNING” or “AUTO TUNING” 
section).

 Press 

the 

MEMO button on the remote 

controller. “– –“ (preset number) starts blinking 
on the display.

  Enter the desired preset number by pressing 

the numeric buttons.

When entering a single digit number (2 for example), 
either input “02” or just input “2” and wait for a few 
seconds.

  Select the desired preset station by pressing 

the F/P and TUNING 

3

 or 

4

 button on the front 

panel 

 Press 

the 

PRESET + or – buttons to select the 

desired preset station, or input your desired 
preset channel with the numeric buttons on 
the remote controller.

 Press 

the 

P.SCAN on the remote controller. 

 

  “PRESET SCAN” appears on the display and 

then the preset station with the lowest preset 
number is recalled fi rst. 

  Preset stations are recalled in sequence (No.1 

→

 No.2 

→

 etc.) for 5 seconds each. 

 

  No stored preset number will be skipped.

  You can fast forward the preset stations by 

pressing the PRESET + continuously. 

 

  When the desired preset station is received, 

cancel the preset scan operation by pressing 
the  CLEAR button or P.SCAN on the remote 
controller.

You can remove preset stations from the memory 
using the following procedure.

  Recall the preset number to be cleared with 

the method described in “Recalling” a preset 
station.

 Press 

the 

MEMORY button on the front panel 

or press the MEMO button on the remote 
controller.

  The stored preset number blinks in the display 

for 5 seconds. While blinking, press the 
CLEAR button on the front panel or the remote 
controller.

  “xx CLEAR” appears on the display to indicate 

that the specified preset number has been 
cleared.

To clear all stored preset stations, press and hold the 
CLEAR and the F/P buttons on the front panel for 
two seconds.