Marantz ud5005 ユーザーガイド
21
Advanced version
Simple version
Information
ENGLISH
Basic version
Playing high-quality audio
( Pure direct function)
This enables you to play high quality audio by stopping the video
signal, etc., output, and outputting the analog audio signal only.
signal, etc., output, and outputting the analog audio signal only.
Press
PURE DIRECT
while stopped.
• The Pure Direct mode changes each time the button is pressed.
Pure Direct1
Pure Direct2
Off
Pure Direct 1
This turns off the digital audio output, video output,
and display. And the FL off indicator lights red.
and display. And the FL off indicator lights red.
Pure Direct 2
This turns off the digital audio output and video
output.
output.
Off
This turns off the pure direct function.
• You cannot use
PURE DIRECT
while the GUI menu is displayed.
• The pure direct setting returns to “Off” when the unit is put in
standby mode.
Basic Settings
This section describes the setting operations for basic settings
available with the remote control.
available with the remote control.
Connections (vpage 9)
Playback (Basic operation) (vpage 13)
n
Changing the brightness of the Display (Dimmer
control) (vpage 21)
n
Playing high-quality audio
(Pure direct function) (vpage 21)
n
HDMI control functions (vpage 21)
n
Video resolution (vpage 22)
n
Adjusting the picture quality (Picture control)
(vpage 23)
n
Mode setting (vpage 24)
Changing the brightness of the
Display ( Dimmer control)
The brightness of the display can be changed.
Press
DIMMER
.
• The brightness changes each time the
button is pressed.
Normal
Dark
Dim
Off
• When the dimmer is set to off, the FL off
indicator lights red.
HDMI control functions
When you make HDMI connections with a TV or AV Receiver
compatible with this unit and HDMI control functions, you can perform
the following operations by setting up the HDMI control functions of
each device.
• TV or AV Receiver power is turned on by operating the unit and
compatible with this unit and HDMI control functions, you can perform
the following operations by setting up the HDMI control functions of
each device.
• TV or AV Receiver power is turned on by operating the unit and
functions change with this unit input.
• Turning off the TV’s power turns the unit’s power to standby.
• Operating the unit via the TV’s remote control.
• Operating the unit via the TV’s remote control.
(When the TV’s remote control has player operation buttons)
1
Set the HDMI control function to “On”.
“HDMI Control” (vpage 34).
2
Turn on all the equipment connected by HDMI cable.
3
Set the HDMI control function for all equipment
connected by HDMI cable.
• Please refer to the owner’s manuals of connected devices for how
to make settings.
• Carry out Steps 2 and 3 if any of the equipment was unplugged.
4
To ensure that the unit’s HDMI video output is
projected on the TV screen, change the input function
of the TV and AV receiver.
5
When you turn the TV’s power to standby, check
that the power of the unit and AV receiver also goes
on standby.
If the HDMI control function does not operate properly, check the
following points.
• Is the TV or AV Receiver compatible with the HDMI control function?
• Are the HDMI control function settings of all equipment correct?
following points.
• Is the TV or AV Receiver compatible with the HDMI control function?
• Are the HDMI control function settings of all equipment correct?
(Step 3)
• After setting, did you add another HDMI device connection or make
any changes in the connections? If so make the settings again.
NOTE
• Some functions may not operate depending on the connected TV or
AV Receiver. Check the owner’s manual of each device for details
beforehand.
beforehand.
• When “HDMI Power Off Control” (vpage 34) is set to “Off”, the
unit does not go to standby even if the connected device is in the
standby mode.
standby mode.
1.UD5005U_ENG_0716.indd 21
2010/07/20 16:50:44