Metabo 600331620 mag 50 magnetic core drill ユーザーガイド
12
ENGLISH
ENG
- Centre the position at which the hole is to be
drilled.
- Align the magnetic drill stand so that the drill bit
is near the centre marking.
- Switch on the magnet of the magnetic drill stand
(switch (11)).
- After releasing the eccentric (13), the upper
section of the magnetic drill stand can be rotated
and laterally shifted so that the drill bit is exactly
above the centre marking. Important! Firmly
clamp the eccentric (13) again.
and laterally shifted so that the drill bit is exactly
above the centre marking. Important! Firmly
clamp the eccentric (13) again.
Before use, always check that the eccentric
(13) is firmly clamped so that accidental
(13) is firmly clamped so that accidental
displacement or rotation of the upper section is not
possible.
possible.
- Then switch on the drill (switch (9)).
- Start the drilling operation with minimum feeding
- Start the drilling operation with minimum feeding
force.
- When the drill bit has started to drill, slightly
higher feeding force can be applied. Excessive
feeding force leads to premature wear of the drill
bit. Ensure that the chip flow is regular
feeding force leads to premature wear of the drill
bit. Ensure that the chip flow is regular
- The graduated collar at the spindle (8) is used to
determine the drilling depth.
If (after use) the magnetic drill stand is placed
on a material with low heat-dissipation char-
on a material with low heat-dissipation char-
acteristics for a long period (e.g. plastic), the
magnet must not be switched on because this
could lead to overheating of the magnetic coils.
magnet must not be switched on because this
could lead to overheating of the magnetic coils.
Perform regular maintenance work, cleaning and
lubrication.
lubrication.
Disconnect the mains plug before starting any
setting, maintenance or repair work.
setting, maintenance or repair work.
For lubricating the rack and pinion that moves the
slide plate (5) up and down, a few drops of oil
should be applied occasionally to the rack.
slide plate (5) up and down, a few drops of oil
should be applied occasionally to the rack.
Coat the sliding surfaces of the slide plate (5) with
multi-purpose grease.
multi-purpose grease.
Backlash of the slide plate
The backlash of the side plate is set ex works.
The side plate (5) must be adjusted so that while
the slide plate (with motor installed) can still be
moved freely up and down, it will remain in any
position without the weight of the drill pulling it
down.
the slide plate (with motor installed) can still be
moved freely up and down, it will remain in any
position without the weight of the drill pulling it
down.
The backlash of the side plate (5) can be adjusted
as required using the seven threaded pins (6).
as required using the seven threaded pins (6).
Release lock nuts, tighten threaded pins and
retighten lock nuts.
retighten lock nuts.
Electronic restart protection (for preventing
accidental restarting)
accidental restarting)
If, with the drill switched on,
a) the magnet is switched off or
b) the power supply is interrupted,
the drill comes to a standstill.
a) the magnet is switched off or
b) the power supply is interrupted,
the drill comes to a standstill.
If the magnet is then reactivated or the power
supply restored, for safety reasons the drill does
not restart automatically (electronic restart protec-
tion). Turn the drill back on at the switch (9).
supply restored, for safety reasons the drill does
not restart automatically (electronic restart protec-
tion). Turn the drill back on at the switch (9).
See also chapter 7.2.
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
need to know the exact model designation of your
power tool.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
www.metabo.com or the main catalogue.
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
qualified electricians ONLY!
The connection cable must only be replaced by
Metabo or an authorised customer service work-
shop.
Metabo or an authorised customer service work-
shop.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
www.metabo.com.
Metabo's packaging can be 100% recycled.
Scrap power tools and accessories contain large
amounts of valuable resources and plastics that
can be recycled.
amounts of valuable resources and plastics that
can be recycled.
These instructions are printed on chlorine-free
bleached paper.
bleached paper.
8
Cleaning, Maintenance
9
Troubleshooting
10 Accessories
11 Repairs
12 Environmental Protection
17026927_0411 M 100.book Seite 12 Dienstag, 26. April 2011 10:28 10