Zhone 2004 ユーザーガイド

IX-3

default 3-2
limits of 3-2

payload scrambling, configuring 4-13
PIM Dense Mode, configuring by port 4-66
PIM neighbor, displaying 4-69
PIM Statistics report 5-9
ping CLI command 6-2
Port IP address

configuring 4-16
unconfiguring 4-17

POTS Statistics report 5-25
POTS, diagnostics 7-1
power

DC adapter 1-4

Power Connection

B-4, B-8

PPP Authorization Entries report 5-27
proprietary voice encapsulation, setting in PVC 4-10
PVC

adding 4-7
deleting 4-12
displaying list of 4-12
modifying 4-9
RFC 1483 4-10
setting proprietary voice encapsulation 4-10
setting RFC 2364 4-10
setting up AAL1/CES 4-11
setting up AAL2/LES 4-11
statistics reports 5-14

Q
quit CLI command 6-2

R
RADIUS

changing encryption secret 3-5
configuration display 3-5
displaying configuration 3-5

RADIUS server 2-9

changing address 3-4
settings 3-4

remove lan ip address CLI command 6-2
rename file CLI command 6-2
reports, list of 5-1
reset system CLI command 6-2
reset, performing hard 3-16
Reverse Path Forwarding 4-66
RFC 1483

setting in PVC 4-10

RFC 2364, setting in PVC 4-10
ring test 7-3
RIP

enabling and disabling 4-19
version, setting 4-20

Route Table report 5-26
route table, displaying 4-27
router

basic setup tasks 4-14
configuration chart 4-15
configuration menu 2-7
configuration, generally 4-15
full-duplex Ethernet option 3-11

RS-232 console port 1-4

S
security level

default passwords for 3-2
privileges 3-1

set bridge global CLI command 6-3
set bridge stp global CLI command 6-3
set dhcp server dns CLI command 6-3
set dhcp server domain CLI command 6-4
set dhcp server enable CLI command 6-3
set dhcp server gateway CLI command 6-3
set dhcp server netbios CLI command 6-3
set dhcp server range CLI command 6-4
set dhcp server subnet CLI command 6-3
set dns server address CLI command 6-4
set ip default route CLI command 6-4
set ip route CLI command 6-4
set lan bridge CLI command 6-4
set lan ip address CLI command 6-5
set lan rip CLI command 6-5
set lan stp bridge CLI command 6-6
set mgcp bracketing CLI command 6-6
set mgcp listening port CLI command 6-6
set mgcp signaling connection CLI Command 6-6
set mgcp signaling port CLI Command 6-7
set mgcp signaling tos CLI Command 6-7
set mgcp voice connection CLI Command 6-7
set mgcp voice tos CLI Command 6-7
set nat CLI Command 6-7
set system defaults CLI Command 6-8
set wan atm ppp auth CLI Command 6-8
set wan atm vc CLI Command 6-8
set wan datalink CLI Command 6-9
set wan framerelay CLI Command 6-9
set wan ip address CLI Command 6-9
set wan rip CLI Command 6-10
set wan stp bridge CLI Command 6-10
show configuration CLI Command 6-11
show dhcp server configuration CLI Command 6-11
show ip routes CLI Command 6-11
SLIC control mode, setting 4-57
SNMP

disabling for IP and EOC 3-7
enabling and disabling via EOC 3-7
enabling and disabling via IP 3-6
enabling for IP and EOC 3-7
MIB support for 3-6
System Contact, configuring 3-7
System Location, configuring 3-8
System Name, configuring 3-8
Trap Host IP address, configuring 3-8

SNMP over EOC (AAL2/LES) 3-5
SNMP traps 3-6, 3-9

restart max delay 3-9

Spanning Tree Bridge priority, configuring 4-33
start mode

displaying 4-53
ground start 4-53
loop start 4-53
setting 4-53

Start Mode Selection menu 4-53
static route

adding 4-18
removing 4-19

STP

enabling and disabling by port 4-33
enabling and disabling globally 4-32

system defaults, setting 3-16
system settings, saving 3-16