ZyXEL P-663H-51 ユーザーガイド
Chapter 9 Quality of Service (QoS)
P-663H-51 User’s Guide
90
IEEE 802.1p specifies the user priority field and defines up to eight separate traffic types. The
following table describes the traffic types defined in the IEEE 802.1d standard (which
incorporates the 802.1p).
following table describes the traffic types defined in the IEEE 802.1d standard (which
incorporates the 802.1p).
9.1.2 IP Precedence
Similar to IEEE 802.1p prioritization at layer-2, you can use IP precedence to prioritize
packets in a layer-3 network. IP precedence uses three bits of the eight-bit ToS (Type of
Service) field in the IP header. There are eight classes of services (ranging from zero to seven)
in IP precedence. Zero is the lowest priority level and seven is the highest.
packets in a layer-3 network. IP precedence uses three bits of the eight-bit ToS (Type of
Service) field in the IP header. There are eight classes of services (ranging from zero to seven)
in IP precedence. Zero is the lowest priority level and seven is the highest.
9.1.3 DiffServ
QoS is used to prioritize source-to-destination traffic flows. All packets in the flow are given
the same priority. You can use CoS (class of service) to give different priorities to different
packet types.
the same priority. You can use CoS (class of service) to give different priorities to different
packet types.
DiffServ (Differentiated Services) is a Class of Service (CoS) model that marks packets so that
they receive specific per-hop treatment at DiffServ-compliant network devices along the route
based on the application types and traffic flow. Packets are marked with DiffServ Code Points
(DSCPs) indicating the level of service desired. This allows the intermediary DiffServ-
compliant network devices to handle the packets differently depending on the code points
without the need to negotiate paths or remember state information for every flow. In addition,
applications do not have to request a particular service or give advanced notice of where the
traffic is going.
they receive specific per-hop treatment at DiffServ-compliant network devices along the route
based on the application types and traffic flow. Packets are marked with DiffServ Code Points
(DSCPs) indicating the level of service desired. This allows the intermediary DiffServ-
compliant network devices to handle the packets differently depending on the code points
without the need to negotiate paths or remember state information for every flow. In addition,
applications do not have to request a particular service or give advanced notice of where the
traffic is going.
9.1.3.1 DSCP and Per-Hop Behavior
DiffServ defines a new DS (Differentiated Services) field to replace the Type of Service
(TOS) field in the IP header. The DS field contains a 2-bit unused field and a 6-bit DSCP field
which can define up to 64 service levels. The following figure illustrates the DS field.
(TOS) field in the IP header. The DS field contains a 2-bit unused field and a 6-bit DSCP field
which can define up to 64 service levels. The following figure illustrates the DS field.
Table 33 IEEE 802.1p Priority Level and Traffic Type
PRIORITY
LEVEL
LEVEL
TRAFFIC TYPE
Level 7
Typically used for network control traffic such as router configuration messages.
Level 6
Typically used for voice traffic that is especially sensitive to jitter (jitter is the variations in
delay).
delay).
Level 5
Typically used for video that consumes high bandwidth and is sensitive to jitter.
Level 4
Typically used for controlled load, latency-sensitive traffic such as SNA (Systems
Network Architecture) transactions.
Network Architecture) transactions.
Level 3
Typically used for “excellent effort” or better than best effort and would include important
business traffic that can tolerate some delay.
business traffic that can tolerate some delay.
Level 2
This is for “spare bandwidth”.
Level 1
This is typically used for non-critical “background” traffic such as bulk transfers that are
allowed but that should not affect other applications and users.
allowed but that should not affect other applications and users.
Level 0
Typically used for best-effort traffic.