Sharp MX-2300N ユーザーガイド
42
OUTPUT
To select output functions and the output tray, touch the [Output] key in the base screen of copy mode. Output functions
that can be selected are sort, group, offset, staple sort, saddle stitch, and punch. All settings are explained in this section
based on the assumption that a saddle stitch finisher, punch module and right tray are installed.
that can be selected are sort, group, offset, staple sort, saddle stitch, and punch. All settings are explained in this section
based on the assumption that a saddle stitch finisher, punch module and right tray are installed.
(1)
[Group] key
This is used to group copies by page.
☞
(2)
[Staple Sort] key
This is used to sort the output into sets, staple each set,
and deliver the sets to the tray. (Note that the sets will not
be offset in the output tray.) When this function is
selected, three keys will appear for selecting the staple
position.
and deliver the sets to the tray. (Note that the sets will not
be offset in the output tray.) When this function is
selected, three keys will appear for selecting the staple
position.
☞
(3)
[Sort] key
This is used to sort (collate) output into sets.
☞
(page 43)
(4)
Output display
An icon will appear to indicate the output mode.
(5)
[Offset Tray] key ([Center Tray] key*)
This is used to offset each set of output from the previous
set in the offset tray (center tray). The [Offset Tray] key is
automatically selected when the [Staple Sort] key is
selected.
* When only a right tray is installed, this appears as the
set in the offset tray (center tray). The [Offset Tray] key is
automatically selected when the [Staple Sort] key is
selected.
* When only a right tray is installed, this appears as the
"Center tray".
(6)
[Right Tray] key
Select this key to have output delivered to the right tray.
When the right tray is selected, offset, staple sort, saddle
stitch, and punch cannot be selected.
When the right tray is selected, offset, staple sort, saddle
stitch, and punch cannot be selected.
(7)
[OK] key
Touch this key to close the output screen and return to
the base screen.
the base screen.
(8)
[Offset] key
This is used to offset each set of output from the previous set.
The offset function operates when the checkbox is
selected
The offset function operates when the checkbox is
selected
and does not operate when the checkbox is
not selected
. (The offset checkmark is automatically
cleared when the staple sort function is selected.)
☞
(9)
[Saddle Stitch] key
This is used to staple and fold each set of copies at the centerline.
☞
When this key is touched, the saddle stitch setting screen
appears. (Only when "Automatic Saddle Stitch" is
enabled in the system settings (administrator).)
appears. (Only when "Automatic Saddle Stitch" is
enabled in the system settings (administrator).)
(10) [Punch] key
This is used to punch holes in the output.
☞
(page 45)
Output
Sort
Staple
Sort
Group
OK
Offset
Tray
Tray
Right Tray
Offset
Saddle
Stitch
Stitch
Punch
(8)
(5)
(3)
(2)
(1)
(7)
(9)
(10)
(4)
(6)
The keys that appear and that can be selected will vary depending on what peripheral devices are installed.
Depending on what peripheral devices are installed, it may not be possible to select certain keys. If your screen is different
from the above screen, see the screens below.
Depending on what peripheral devices are installed, it may not be possible to select certain keys. If your screen is different
from the above screen, see the screens below.
Display example 1
The screen when a right tray, finisher,
and saddle finisher are not installed.
The screen when a right tray, finisher,
and saddle finisher are not installed.
Display example 2
The screen when a right tray is installed.
The screen when a right tray is installed.
Display example 3
The screen when a right tray, finisher
and punch module are installed.
The screen when a right tray, finisher
and punch module are installed.
Output
Sort
Group
OK
Offset
Center
Tray
Tray
Right Tray
Output
Sort
Group
OK
Offset
Staple
Sort
Punch
Offset
Tray
Tray
Right Tray
Output
Sort
Group
OK
Offset