Sharp MX-5500N 操作ガイド
61
Device Control
These settings control devices installed on the machine. Touch the [Device Control] key to configure the settings.
Other Settings
Original Feeding Mode
The following original feeding modes can be set to
operate by default in copy, Scan to HDD, and image
send modes. When a mode is frequently used, this
saves you from having to select the mode in the special
modes each time you need to use it.
operate by default in copy, Scan to HDD, and image
send modes. When a mode is frequently used, this
saves you from having to select the mode in the special
modes each time you need to use it.
• Mixed Size Original (Same Width/Different Width)
• Slow Scan Mode
• Slow Scan Mode
Saddle Stitch Position Adjust
(When a saddle stitch finisher is installed.)
When a saddle stitch finisher is installed, this setting is
used to adjust the stapling position (folding position) of
the pamphlet staple function.
The value can be adjusted in increments of 0.25 mm
within a range of ±2.0 mm from the home position of
each paper size.
used to adjust the stapling position (folding position) of
the pamphlet staple function.
The value can be adjusted in increments of 0.25 mm
within a range of ±2.0 mm from the home position of
each paper size.
Auto Paper Selection Setting
The paper types* that the Auto Paper Selection function will
select can be specified. Select one of the following settings:
select can be specified. Select one of the following settings:
• Plain Paper
• Plain and Recycle Paper
• Recycle Paper
• Plain and Recycle Paper
• Recycle Paper
The Auto Paper Selection function will not select any
paper types other than the paper types specified with
this setting.
* The paper type set for each paper tray using "
paper types other than the paper types specified with
this setting.
* The paper type set for each paper tray using "
(general).
Tandem Connection Setting
When two machines are used as network printers using
TCP/IP protocol, use this setting to configure the port
number and IP address of the machine used as the
tandem slave machine.
TCP/IP protocol, use this setting to configure the port
number and IP address of the machine used as the
tandem slave machine.
Disabling of Master Machine Mode
To prohibit tandem transmission, enable this setting.
(There is normally no need to enable this setting.)
To prohibit tandem transmission, enable this setting.
(There is normally no need to enable this setting.)
Disabling of Slave Machine Mode
To prohibit tandem reception, enable this setting. (There
is normally no need to enable this setting.)
To prohibit tandem reception, enable this setting. (There
is normally no need to enable this setting.)
Detect Standard in Auto Color
Mode
Mode
When the color mode is set to auto in copy mode, the
discrimination point for detecting whether originals are
color or black and white can be set to one of 5 levels. To
make it easier to detect a black and white original, adjust
the setting toward [Black & White]. To make it easier to
detect a color original, adjust the setting toward [Color].
discrimination point for detecting whether originals are
color or black and white can be set to one of 5 levels. To
make it easier to detect a black and white original, adjust
the setting toward [Black & White]. To make it easier to
detect a color original, adjust the setting toward [Color].
Auto Switching of Finisher Trays
If the number of sheets on the upper finisher tray
reaches the sheet limit, output will automatically switch
to the lower tray.
reaches the sheet limit, output will automatically switch
to the lower tray.
1
2
12
11
Position moved in
the minus direction.
the minus direction.
Position moved in
the plus direction.
the plus direction.
Max. + 2 mm
Min. - 2 mm
Reference position
• The factory default setting for the port number is
[50001]. Unless you experience difficulty with this
setting, do not change the port number.
setting, do not change the port number.
• To use the tandem function when user
authentication is enabled, the same login name and
password must be used on both the master
machine and slave machine. If the same login name
and password are not used, the page count may not
be added to the appropriate user count or only the
master machine may print.
password must be used on both the master
machine and slave machine. If the same login name
and password are not used, the page count may not
be added to the appropriate user count or only the
master machine may print.