Crown ct-1600 補足マニュアル
Com-Tech 1600 Amplifier Service Manual
26
Q42973-0 Output Module (P10337-7 board) Parts List
Capacitors
C01
C 8511-5
.047µF
C02
C 8426-6
.1µF
C03
C 8426-6
.1µF
C04
C 6806-1
.01µF
C05
C 6806-1
.01µF
C06
C 6806-1
.01µF
C07
C 6807-9
.001µF
C08
C 6810-3
180pF
C09
C 6809-5
220pF
C43
C 7697-3
.01µF
Diodes
D01
C 2851-1
1N4004
D02
C 2851-1
1N4004
D03
C 2851-1
1N4004
D04
C 2851-1
1N4004
D05
C 2941-0
1N5402
D06
C 2941-0
1N5402
D07
C 2941-0
1N5402
D08
C 2941-0
1N5402
D09
C 2851-1
1N4004
D10
C 2851-1
1N4004
D11
C 2851-1
1N4004
D12
C 2851-1
1N4004
Inductors
L00
C 6592-6
Output Coil
L01
C 3510-2
470µH
L02
C 3510-2
470µH
Transistors
Q17
C 8508-1
NPN 2SC3298B
Q19
C 8509-9
PNP 2SA1306B
Resistors
R00
A10266-7501
75
R01
A10266-1011
100
R02
C 7778-1
5.6 .5W Flame Proof
R03
D 6486-2
.2 5W
R04
D 6486-2
.2 5W
R05
D 6486-2
.2 5W
R06
D 6486-2
.2 5W
R07
D 6486-2
.2 5W
R08
D 6486-2
.2 5W
R09
C 7779-9
22 .5W Flame Proof
R10
A10266-1011
100
R11
C 7317-8
2.7 5W
R12
A10266-2R73 2.7 1W
R13
A10266-7501
75
R14
A10266-2R73 2.7 1W
R15
D 6486-2
.2 5W
R16
D 6486-2
.2 5W
R17
D 6486-2
.2 5W
R18
D 6486-2
.2 5W
R19
D 6486-2
.2 5W
R20
D 6486-2
.2 5W
R21
C 7778-1
5.6 .5W Flame Proof
R22
C 7779-9
22 .5W Flame Proof
R23
C 6844-2
250 Pot LS
R24
A10266-1331
13K
R25
A10266-2221
2.2K
R26
C 6844-2
250 Pot HS
R27
A10266-3911
390
R28
A10266-1331
13K
R29
A10266-5101
51
R30*
A10265-10201* 102*
Misc.
Board
P10337-7
Jumpers
C 5868-2
0 Ohm (Qty 6)
Clips
D 6414-3
Q17/Q19
J500
J600
C 7057-0
10 Pin Header
*Note: R30 is 102 Ohms in most units, though in some
cases a different value may be used to match the
installed S100/S200 LM334 (C5826-0) device grade.
This is the standard value and is used with the most
common LM334 grade, green. If the LM334 is marked
with a blue dot, R30 should be a 107 Ohm resistor
(A10265-10701); if it is marked with a yellow dot then
R30 should be a 100 Ohm resistor (A10265-10001).
cases a different value may be used to match the
installed S100/S200 LM334 (C5826-0) device grade.
This is the standard value and is used with the most
common LM334 grade, green. If the LM334 is marked
with a blue dot, R30 should be a 107 Ohm resistor
(A10265-10701); if it is marked with a yellow dot then
R30 should be a 100 Ohm resistor (A10265-10001).
Note:
Note:
Note:
Note:
Note: Q18, S100, Driver Transistors, and Output
Transistors are not included with Output Module. See
Output Assembly parts list for these part numbers.
Transistors are not included with Output Module. See
Output Assembly parts list for these part numbers.