Crown xls 202 仕様ガイド

Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.
Crosstalk (below rated power)

at 1 kHz:  –82 dB.
at 20 kHz:  –58 dB.

Voltage Gain (at maximum output): 31 dB.

Output Power: 

Load Impedance: Safe with all types of loads. 

Rated for 2 to 8 ohms in Stereo, 8 ohms in 

Bridge-Mono.
AC Line Voltages Available (±10%): 120 and 

230 VAC.
Line Frequency: 50/60 Hz.

he XLS Series of power amplifiers from 

Crown represents a new era in affordable, 

quality power amplification. The line con-

sists of three models in a uniform, rugged 

chassis, incorporating the best of tried-and-true 

design principles and innovative features.
XLS Series amplifiers are professional stereo 

power amplifiers engineered to meet demand-

ing audio requirements—reliably and within 

budget. Plus, every XLS Series amplifier is 

backed by Crown’s unequaled Three-Year, No-

Fault, Fully-Transferrable Warranty that covers 

everything.
With over five decades of experience designing 

and building rock-solid products, Crown is the 

standard in amp technology. So check out the 

affordable, Crown XLS Series. They are a pow-

erful argument for quality and value!
For more details about the XLS Series, 

contact the Crown Technical Support Group at 

800-342-6939 or 219-294-8200. Also, visit the 

Crown Audio website at www.crownaudio.com.

The following applies to units in Stereo mode with 8-ohm loads 

and rated input sensitivity unless otherwise specified.

Sensitivity (volts RMS) for full rated power at 

4 ohms: 0.725.
Frequency Response (at 1 watt) 20 Hz to 20 

kHz: ±0.75 dB. 
Phase Response (degrees at 1 watt) 

at 10 Hz:  –10.
at 20 kHz: +19.

Signal-to-Noise Ratio (20 Hz to 20 kHz)

A-weighted, below rated power: > 100 dB.
No weighting, below rated power: > 97 dB.

Total Harmonic Distortion (THD) at full band-

width power, from 20 Hz to 1 kHz: < 0.15%.
Intermodulation Distortion (IMD) (60 Hz and 

7 kHz at 4:1) from full rated output to –40 dB: 

< 0.3%.

Level: Two front-panel, black rotary level 

controls, one for each channel. 
Power: Front-panel switch; on when in the UP 

position.
Filter Switches: One per channel; three-posi-

tion back-panel switches set the frequency 

for internal high-pass filters. Frequency set-

ting is 30 Hz when switch is in left position; 

15 Hz when switch is centered; and bypassed 

when switch is in right position.
Limiter Switch: Back-panel switch offers loud-

speaker protection against moderate amplifier 

clip when set to the “IN” position.
Fuse: Provides overload protection.

Clip: Two front-panel red LEDs, one for each 

channel, illuminate when the channel’s output 

signal is being overdriven.
Power: Green front-panel LED indicates 

amplifier has been turned on and AC power 

is available.
Fault: Yellow front-panel LED illuminates 

when amplifier is in protect mode. Also illumi-

nates briefly during normal power-up when 

amplifier is first switched on.

8-ohm Stereo (per channel)

1 kHz 

Power

2-ohm Stereo (per channel)

4-ohm Stereo (per channel)

*1 kHz Power: refers to maximum average power in watts 

at 1 kHz with 0.1% THD.

*