Jet benchtop wood-cutting band saw - 10" wheel diameter - jwbs10os ユーザーガイド
15
Grounding Instructions
General Information
This Band Saw must be
grounded while in use to protect the operator
from electric shock.
from electric shock.
In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric
shock. This tool is equipped with an electric cord
having an equipment-grounding conductor and a
grounding plug that looks similar to the plug in
Figure 15. The plug must be inserted into a
matching outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
grounding provides a path of least resistance for
electric current to reduce the risk of electric
shock. This tool is equipped with an electric cord
having an equipment-grounding conductor and a
grounding plug that looks similar to the plug in
Figure 15. The plug must be inserted into a
matching outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Do not modify the plug provided. If it will not fit
the outlet, have the proper outlet installed by a
qualified electrician.
the outlet, have the proper outlet installed by a
qualified electrician.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. The conductor, with insulation
having an outer surface that is green with or
without yellow stripes, is the equipment-
grounding conductor. If repair or replacement of
the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a
live terminal.
grounding conductor can result in a risk of
electric shock. The conductor, with insulation
having an outer surface that is green with or
without yellow stripes, is the equipment-
grounding conductor. If repair or replacement of
the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a
live terminal.
Figure 15
Check with a qualified electrician or service
personnel if the grounding instructions are not
completely understood, or if in doubt as to
whether the tool is properly grounded.
personnel if the grounding instructions are not
completely understood, or if in doubt as to
whether the tool is properly grounded.
Repair or replace a damaged or worn cord
immediately.
immediately.
115 Volt Operation
As received from the factory, your bandsaw is
ready to run at 115-volt operation. This bandsaw
ready to run at 115-volt operation. This bandsaw
is intended for use on a circuit that has an outlet
and a plug that looks like the one illustrated in
Figure 4. An adapter with a grounding ear
(Figure 16) may be used temporarily to connect
this plug to a two-pole receptacle as shown
and a plug that looks like the one illustrated in
Figure 4. An adapter with a grounding ear
(Figure 16) may be used temporarily to connect
this plug to a two-pole receptacle as shown
(Figure 11), if a properly grounded outlet is not
available. The temporary adapter should only be
used until a properly grounded outlet can be
installed by a qualified electrician. This adapter
is not applicable in Canada. The green colored
rigid ear, lug, or tab, extending from the adapter,
must be connected to a permanent ground such
as a properly grounded outlet box, as shown in
Figure 5.
available. The temporary adapter should only be
used until a properly grounded outlet can be
installed by a qualified electrician. This adapter
is not applicable in Canada. The green colored
rigid ear, lug, or tab, extending from the adapter,
must be connected to a permanent ground such
as a properly grounded outlet box, as shown in
Figure 5.
Figure 16
Extension Cords
Use only three wire extension cords that have
three-prong grounding plugs and three-pole
receptacles that accept the tool’s plug.
three-prong grounding plugs and three-pole
receptacles that accept the tool’s plug.
Make sure the cord is in good condition and
heavy enough to carry the current your band
saw will draw. An undersized cord will cause a
drop in line voltage, resulting in loss of power
and overheating. Table 1 shows the correct size
to use depending on cord length and the ampere
rating on your machine’s nameplate. If in doubt,
use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
heavy enough to carry the current your band
saw will draw. An undersized cord will cause a
drop in line voltage, resulting in loss of power
and overheating. Table 1 shows the correct size
to use depending on cord length and the ampere
rating on your machine’s nameplate. If in doubt,
use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
Repair or replace a damaged or worn cord
immediately.
immediately.
Power
Extension Cord
Currant
(Amps)
Line
voltage
Cord length
in feet
Cord gauge
(AWG)
0-6
120
0 to 25
18
25 to 50
16
50 to 100
16
over 100
14
6-10
120
0 to 25
18
25 to 50
16
50 to 100
14
over 100
12
10-12
120
0 to 25
16
25 to 50
16
50 to 100
14
over 100
12
12-16
120
0 to 25
14
25 to 50
12
over 50
not recommended
Table 1