Maytag MER8772W ユーザーズマニュアル

Bridge Element

Use the bridge area to create an oblong heated area to cook with
large cookware.

To use SINGLE (A):

1. Push in and turn left front control knob clockwise from the Off

position to the SINGLE zone anywhere between LOW and
HIGH.

2. Turn control knob to Off when finished.

To use SINGLE (C):

1. Push in and turn left rear control knob counterclockwise from

the Off position to anywhere between LOW and HIGH.

2. Turn control knob to Off when finished.
To use SINGLE and BRIDGE area (A+B):

1. Push in and turn left front control knob counterclockwise from

the Off position to the BRIDGE zone anywhere between LOW
and HIGH.

2. Turn both control knobs to Off when finished.
To use both SINGLE elements and BRIDGE (A+B+C):

1. Push in and turn left front control knob counterclockwise from

the Off position to the BRIDGE zone anywhere between LOW
and HIGH.

2. Push in and turn left rear control knob counterclockwise from

the Off position to anywhere between LOW and HIGH.

3. Turn both control knobs to Off when finished.
To use both SINGLE elements (A+C):

1. Push in and turn left front control knob clockwise from the Off

position to the SINGLE zone anywhere between LOW and
HIGH.

2. Push in and turn left rear control knob counterclockwise from

the Off position to anywhere between LOW and HIGH.

3. Turn control knob to Off when finished.

OVEN USE

Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled.

IMPORTANT: The health of some birds is extremely sensitive to the
fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well-
ventilated room.

Electronic Oven Controls

Control Display

The display will flash when powered up or after a power loss. Press
CANCEL to clear. When oven is not in use, the time of day is
displayed. Indicator lights show functions that are in use.

Tones

Tones are audible signals, indicating the following:
One tone

■

Valid pad press

■

Oven is preheated (long tone)

■

Function has been entered

■

Reminder (on some models), repeating each minute after the
end-of-cycle tones

Three tones

■

Invalid pad press

Four tones

■

End of cycle

To Change Tone Settings:

Tone Pitch

Sets the pitch of the tone to either high or low.
Press and hold BROIL for 5 seconds. “TONE PITCH HIGH” or
“TONE PITCH LOW” will appear in the display. Press and hold
BROIL again to change setting.

To exit, press CANCEL.

Key Press Tones

Activates or turns off the tones when a keypad is pressed.
Press and hold KEEP WARM for 5 seconds. “KEY PRESS TONES
ON” or “KEY PRESS TONES OFF” will appear in the display. Press
and hold KEEP WARM again to change setting.
To exit, press CANCEL.
End of Cycle Tone

Activates or turns off the tones that sound at the end of a cycle.
Press and hold CONVECT BAKE for 5 seconds. “CYCLE END
TONE ON” or “CYCLE END TONE OFF” will appear in the display.
Press and hold CONVECT BAKE again to change setting.
To exit, press CANCEL.

Reminder Tones Disable

Turns off the short tones that sound 1 minute after the end of cycle
tones.
Press and hold BAKE for 5 seconds. “REMINDER TONES ON” or
“REMINDER TONES OFF” will appear in the display. Press and
hold BAKE again to change setting.
To exit, press CANCEL.
Audible Tones Disable

Turns off all tones, including the end of cycle tone and key press
tones. Reminder tones are still active when all tones are disabled.
Press and hold CLOCK for 5 seconds. “ALL SOUNDS ON” or “ALL
SOUNDS OFF” will appear in the display. Press and hold CLOCK
again to change setting.
To exit, press CANCEL.

A. Left front single element
B. Left center bridge element

C. Left rear single element

Left Front Control

Left Rear Control