Electrolux ew36ec55g ユーザーズマニュアル
14
Setting Surface Controls
OPERATING THE DUAL SURFACE RADIANT ELEMENT
Both the 30” and 36” cooktops are equipped with dual radiant surface element
located as shown in Figs. 1 & 2. A touch key pad on the element controls is
used to select one of the 2 positions of the element. Indicator lights on the
control panel are used to indicate which coil of the dual radiant element will
heat. One indicator light on indicates that only the INNER coil will heat (Fig. 3).
Two indicator lights on indicate that both INNER and OUTER coils will heat
(Fig. 4). You may switch from either coil setting at any time during cooking.
located as shown in Figs. 1 & 2. A touch key pad on the element controls is
used to select one of the 2 positions of the element. Indicator lights on the
control panel are used to indicate which coil of the dual radiant element will
heat. One indicator light on indicates that only the INNER coil will heat (Fig. 3).
Two indicator lights on indicate that both INNER and OUTER coils will heat
(Fig. 4). You may switch from either coil setting at any time during cooking.
!
CA
CA
CA
CA
CAUTION
UTION
UTION
UTION
UTION
Radiant surface elements may appear to be cooled after they have been turned OFF. The Hot Surface
Indicator Light will turn ON and will continue to glow until the glass cooktop has cooled down to a
moderate level. The glass surface may still be hot and burns may occur if the glass surface is touched
before the indicator light has turned OFF.
Indicator Light will turn ON and will continue to glow until the glass cooktop has cooled down to a
moderate level. The glass surface may still be hot and burns may occur if the glass surface is touched
before the indicator light has turned OFF.
To Operate the Dual Surface Element:
1.
Place correctly sized cookware on the radiant surface element.
2.
Touch and hold the
POWER
key pad until a beep sound. The power
indicator light above the
POWER
will turn ON. Note: If no other key pad is
touched within 20 seconds the request to Power ON the cooktop will
clear.
clear.
3.
Touch and hold the
ON OFF
pad for the dual element position until a beep
is heard. The indicator light located above the
ON OFF
pad will glow.
Note: If no further pads are touched within 10 seconds the request to
power the element ON will clear.
power the element ON will clear.
4.
Select the INNER (Fig. 3) or INNER and OUTER (Fig. 4) to heat by touching the
size
key
pad.
5.
Touch
pad once to turn ON the power level to HI. Touch
med
pad once for
MEDIUM, touch
pad once for power level to LO or touch
warm
pad once to set the
power level to KEEP WARM setting.
6.
Each touch of the
or
pad will increase or decrease the power level. Lo is
the lowest power level available. Note: The power level may be adjusted at any time
while the element is ON.
while the element is ON.
7.
Start most cooking operations on a higher setting and then turn to a lower setting to finish
cooking. Each surface element provides a constant amount of heat at each setting. A
glowing red surface heating area extending beyond the bottom edge of the cookware
indicates the cookware is too small for the surface heating area.
cooking. Each surface element provides a constant amount of heat at each setting. A
glowing red surface heating area extending beyond the bottom edge of the cookware
indicates the cookware is too small for the surface heating area.
8.
When cooking has been completed touch the
ON OFF
pad once to turn the element OFF
and if no other surface element is used touch the
POWER
key pad to turn off the
cooktop.Note: The Hot Surface Indicator Light will turn ON if the cooktop is still
hot and will remain ON until the heating surface area has cooled sufficiently.
hot and will remain ON until the heating surface area has cooled sufficiently.
Fig. 3
Fig. 4
lock
POWER
warm
size
ON OFF
ON OFF
hot surface
med
hot surface
med
timer
ON OFF
size
hot surface
med
ON OFF
hot surface
med
lock
POWER
timer
warm
size
ON OFF
ON OFF
ON OFF
ON OFF
size
ON OFF
size
hot surface
med
hot surface
med
hot surface
med
hot surface
med
hot surface
med
Fig. 1
Fig. 2