DeWALT dw7353 chip collection accessory ユーザーガイド
DW7353
CHIP COLLECTION ACCESSORY
CHIP COLLECTION ACCESSORY
WARNING: For your own safety, read the tool instruction manual
before using any accessory. Failure to heed these warnings may result
in personal injury and serious damage to the planer and the acces-
sory. When servicing this tool, use only identical replacement parts.
in personal injury and serious damage to the planer and the acces-
sory. When servicing this tool, use only identical replacement parts.
Unpacking the Chip Collection Kit
In addition to these instructions, the carton should contain:
• 1 chip collector with 4" hose with drum bonnet and 1 hose clamp
with ground wire attached
Assembly
WARNING: TURN OFF AND UNPLUG PLANER BEFORE
MAKING ANY ADJUSTMENTS OR REMOVING OR INSTALLING
ATTACHMENTS OR ACCESSORIES.
ATTACHMENTS OR ACCESSORIES.
TO ATTACH THE ROUND DUST PORT TO THE PLANER (FIG. 1)
1. Depress the lock button (A) on the chip ejection chute (B), shown
in Figure 1.
2. Slide the notches in the round dust port (C) over the pins on the
chip ejection chute (Fig. 2).
3. Rotate the round dust port until the button engages the dust
ejection chute and locks in place.
TO ATTACH THE HOSE AND GROUND WIRE TO
THE DUST PORT (FIG. 2)
THE DUST PORT (FIG. 2)
WARNING: Do not use the chip collection accessory without
attaching the ground wire to the planer. Static electricity may create
sparks that would risk a fire hazard.
sparks that would risk a fire hazard.
1. Fit the end of the chip ejection hose around the outside of the
round dust ejection port on the planer.
2. Tighten the screw on the clamp (D) to secure the hose to the port.
3. Attach the end of the ground wire (E) to one of the two screws on
3. Attach the end of the ground wire (E) to one of the two screws on
the rear of the planer body (F).
TO ATTACH CHIP COLLECTOR TO THE
COLLECTION CONTAINER
COLLECTION CONTAINER
1. Select a container with a rim or edge that the drawstring collar (G)
will attach to securely (Fig. 3).
2. Drape the drum bonnet (H) of the chip collector over the outside
rim of the container (Fig. 4).
3. Press the lock button (I) and pull the drawstring collar on the bag
as tight as possible to secure. Release the lock button to hold
drawstring in place.
drawstring in place.
WARNING: DON’T USE IN DANGEROUS ENVIRONMENT. Don’t
use power tools in damp or wet locations, or expose them to rain.
Keep work area well lighted. Always operate tool in a well-ventilated
area free of combustible materials, gasoline or solvent vapors. If
sparks come in contact with flammable vapors, they may ignite, caus-
ing fire or explosion.
Keep work area well lighted. Always operate tool in a well-ventilated
area free of combustible materials, gasoline or solvent vapors. If
sparks come in contact with flammable vapors, they may ignite, caus-
ing fire or explosion.
WARNING: Clean out your tool often, especially after heavy
use. Dust and grit containing metal particles often accumulate on
interior surfaces and could create a risk of serious injury, electric
shock or electrocution. ALWAYS WEAR SAFETY GLASSES.
interior surfaces and could create a risk of serious injury, electric
shock or electrocution. ALWAYS WEAR SAFETY GLASSES.
WARNING: Never clear clogs, make cutter knife replacement, or
any other repairs/adjustments with unit plugged in.
The Hose
NOTE: The hose measures 8' long. For proper air flow, suspend the
hose from above or cut the hose to length.
hose from above or cut the hose to length.
CAUTION: It is not recommended that the hose sag over the edge
of the collection container. The system may not work properly while
the bag is weighed down by the sagging hose.
the bag is weighed down by the sagging hose.
D
E
WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
(JUN03) Form No. 619016-00 DW7353 Copyright © 2003
The following are trademarks for one or more D
E
WALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box
configuration; and the array of lozenge-shaped humps on the surface of the tool.
B
A
C
I
D
E
F
G
H
TO SHORTEN THE LENGTH OF THE HOSE (FIG. 4)
1. Loosen the screw on the clamp and remove the clamp from the
hose.
2. Measure the desired length of the hose.
3. Cut through the hose and the wire with snips at desired length.
4. Reattach the clamp on the cut end of the hose.
3. Cut through the hose and the wire with snips at desired length.
4. Reattach the clamp on the cut end of the hose.
TO SUSPEND THE HOSE (FIG. 5)
1. Remove the hose from the planer.
2. Select an item above the work area that is secure and will support
2. Select an item above the work area that is secure and will support
the weight of the hose (i.e., an anchored pipe, an anchored hook,
or a rafter).
or a rafter).
3. Suspend the hose by the selected support and reattach the hose
to the planer.
WARNING: Chips are ejected at significant velocity. Keep hands
and face clear of dust ejection port.
WARNING: DO NOT OPERATE YOUR PLANER WITHOUT A
DUST EJECTION PORT LOCKED INTO PLACE. DO NOT INSERT
ANYTHING INTO THE DUST EJECTION CHUTE UNLESS THE
PLANER IS UNPLUGGED AND YOU ARE CLEARING A CLOG OR
OBSTRUCTION IN THE UNIT. DO NOT ALLOW YOUR FACE OR
EYES NEAR THE DUST EJECTION PORT WHEN THE PLANER IS
IN OPERATION. SERIOUS INJURY COULD RESULT.
ANYTHING INTO THE DUST EJECTION CHUTE UNLESS THE
PLANER IS UNPLUGGED AND YOU ARE CLEARING A CLOG OR
OBSTRUCTION IN THE UNIT. DO NOT ALLOW YOUR FACE OR
EYES NEAR THE DUST EJECTION PORT WHEN THE PLANER IS
IN OPERATION. SERIOUS INJURY COULD RESULT.
C
FIG. 1
FIG. 2
FIG. 3
FIG. 4
FIG. 5
G