Garmin gps 60 クイック設定ガイド

Your GPS 60 shows all the information you need to navigate 

on five Main Pages (or screens): the Satellite Page, Trip Computer 
Page, Map Page, Compass Page, and Main Menu Page. Press the 
PAGE key to see each Main Page in the order shown.

To enter or change data, use the ROCKER key and the 

ENTER key. Press the ROCKER key left, right, up, or down to 
highlight a field you want to change. Press ENTER to select the 
field. Then use the ROCKER key to select options from a menu 
and press ENTER.

You may need to enter words or 

numbers with the ROCKER key and an 
on-screen keyboard. To enter data, use 
the ROCKER key to highlight a letter or 
number. Press ENTER to select the highlighted letter or number. 
Continue choosing letters with the ROCKER and ENTER keys. 
When you are finished, highlight ‘OK’ and press ENTER.

The GPS 60 operates on two AA batteries (not included). Alka-

line or NiMH batteries may be used (see the Owner’s Manual for 
directions to set the battery type). Stored data will not be lost when 
batteries are removed.

1.  Remove the battery cover by 

lifting the D-ring, turning it 
1/4 turn counterclockwise, and 
then pulling the cover away.

2.  Insert the batteries, observing 

the proper polarity.

3.  Reinstall the battery cover by 

connecting the bottom of the 
cover to the bottom of the 
unit. Make sure the tab on the 
cover fits into the slot on the 
unit. Press the cover closed 
and turn the D-ring clockwise 
to lock.

Battery Information

•  When replacing batter-

ies, use only new or fully 
charged batteries.

•  Do not mix Alkaline and 

NiMH batteries. 

•  Disposable batteries typically 

last longer than rechargeable 
batteries. 

•  Extensive use of backlight-

ing, WAAS, or key beep 
tones significantly reduces 
battery life.

Before you can begin using your GPS 60, you must wait for the 

GPS to initialize. This process allows the GPS 60 to receive and store 
satellite information and begin using the satellites for navigation. 
Initialization happens automatically and should take no more than a 
few minutes.

1.  Take your GPS 60 outside where it 

has a clear view of the sky and turn 
it on. The Welcome Page appears, 
followed by the Satellite Page.

2.  Wait while the GPS 60 searches for 

satellite signals. While the unit is 
searching, you will see the message 
‘Acquiring Satellites.’

3.  Once your GPS 60 has acquired 

satellites, your location in coordinates 
appears at the top of the page.

If, for some reason, the GPS 60 is not able to gather the neces-

sary satellite information, try moving away from tall buildings, 
trees, or other obstructions. Refer to your Owner’s Manual for more 
instructions.

If you cannot see the screen of your GPS 60 clearly, adjust the 

brightness and contrast of the backlight.

1.  Press and release the POWER key.
2.  Press the ROCKER key up or down to increase 

or decrease screen brightness.

3.  Press the ROCKER key left or right to change 

the screen contrast. Press QUIT to exit.

POWER Key—Press and hold to turn unit on/off. 
Press and release to adjust backlighting and contrast.

IN/OUT Zoom Keys—From the Map Page, press and 
release to zoom in or out. From any other page, press 
to scroll up or down a list

FIND Key—Press and release at any time to view the 
Find Page. Press and hold for Man Overboard.

MARK Key—Press and release at any time to mark 
your current location as a waypoint.

QUIT Key—Press and release to cancel data entry or 
to exit a page or menu.

PAGE Key—Press and release to cycle through the 
Main Pages. Press to close the on-screen keyboard.

MENU Key—Press and release to view a menu for 
each page. Press twice to view the Main Menu.

ENTER Key—Press and release to select highlighted 
options and data or confirm on-screen messages.

ROCKER Key—Press left, right, up, or down to move 
through lists, highlight fields, on-screen buttons, and 
icons, enter data, or move the map panning arrow.

D-Ring

Battery Cover

Battery Compartment

USE BY

: 2009

USE BY

: 2009