Atlantic Technology icts 6.3 インストール手順
Installation Instructions
Rough In Kit Information for
IWTS 6 CMS and IWTS 8 CMS
Ceiling Speaker
Preparation
Rough-In Wall And Ceiling Bracket The bracket is designed
to facilitate the installation of these speakers in new construction
projects. The bracket not only gives you a solid metal mounting frame
for extra support of the speaker, but also assures that the cut outs for
the speakers are of the proper size and location. The bracket is de-
signed so that the mounting arms will span studs or joists on either
16" or 24" centers. The flange may be oriented either in a horizontal
or vertical fashion.
Ceiling Speaker Back Box The installer must be certain
that there is sufficient room for the speaker back box and rough in
bracket and that lead wires and electrical conduit can be brought to
the planned location. 1/2" conduit electrical knock-outs are provided
on all four sides of the back box for wiring convenience.
The following kits will be availble:
IC-NC-6 New Construction Kit for the 6 CMS. Includes two mount-
ing rails and a steel plate for locating the speaker in the wallboard.
IC-NC-6 New Construction Kit for the 8 CMS. Includes two mount-
ing rails and a steel plate for locating the speaker in the wallboard
IC-BOX-6/8 Back Box for either a 6 or 8 CMS speaker. The back
box mounts to the rails included with the New Construction Kit. The
appropriate kit must be ordered to install the back box.
to facilitate the installation of these speakers in new construction
projects. The bracket not only gives you a solid metal mounting frame
for extra support of the speaker, but also assures that the cut outs for
the speakers are of the proper size and location. The bracket is de-
signed so that the mounting arms will span studs or joists on either
16" or 24" centers. The flange may be oriented either in a horizontal
or vertical fashion.
Ceiling Speaker Back Box The installer must be certain
that there is sufficient room for the speaker back box and rough in
bracket and that lead wires and electrical conduit can be brought to
the planned location. 1/2" conduit electrical knock-outs are provided
on all four sides of the back box for wiring convenience.
The following kits will be availble:
IC-NC-6 New Construction Kit for the 6 CMS. Includes two mount-
ing rails and a steel plate for locating the speaker in the wallboard.
IC-NC-6 New Construction Kit for the 8 CMS. Includes two mount-
ing rails and a steel plate for locating the speaker in the wallboard
IC-BOX-6/8 Back Box for either a 6 or 8 CMS speaker. The back
box mounts to the rails included with the New Construction Kit. The
appropriate kit must be ordered to install the back box.
343 Vanderbilt Avenue Norwood, MA 02062
(781) 762-6300 www.atlantictechnology.com
010-1082
Assembly and Installation
Back BoxDimensions with Bracket:
15"W x 15-1/8"L x 6-1/2"D
If you are using a Ceiling Speaker Back Box, start with Step 1.
Otherwise, skip to Step 3 for Rough In Bracket assembly and instal-
lation.
Otherwise, skip to Step 3 for Rough In Bracket assembly and instal-
lation.
1
Attach the rough in bracket flange, tabs facing out, to the
enclosure with the (2), #8 sheet metal screws provided.
2
Punch out one of the 4 knock-outs on the side of the enclosure
to bring in the speaker wire and attach a 1/2" conduit nipple
if necessary.
if necessary.
3
Slide one side of the flange of the bracket (or bracket/box as-
sembly) into one of the mounting arms, making certain that
it seats all the way under the rolled-over edge of the arm.
it seats all the way under the rolled-over edge of the arm.
4
Slide the other arm onto the opposite side of the flange. Make
certain the arms are located evenly on the flange.
5
Measure the mounting location of the bracket (or bracket/
box) assembly against the stud work and attach it to the
studs with nails or screws. Make sure the flange is facing
outward.
studs with nails or screws. Make sure the flange is facing
outward.
NOTE: The bracket (or bracket/box) assembly may be slid from
side to side on the arms after the bracket is mounted for final
position adjustment. Do not mount the assembly closer than
1-1/2” to a stud or joists to allow the clamping feet to swing
freely for clamping the speaker assembly in the wall or ceiling.
6
Route the speaker wire through the knock-out hole in the
back box and attach conduit if necessary to the installed
nipple.
nipple.
7
After the sheet rock or ceiling tiles are installed, the mounting
hole for the ceiling speaker may be cut out and the speaker
installed as normal with the clamping feet securing the as-
sembly together.
installed as normal with the clamping feet securing the as-
sembly together.
Side Rails (2 pcs)
Back Box Speaker
Enclosure
#8 Philips Sheet
Metal Screw (2 pcs)
Metal Screw (2 pcs)
Rough In Bracket