Alpine cva-1014 ユーザーガイド
38
-EN
Other Useful Features
Setting the XM Auxiliary Data Field
(ADF)
(ADF)
The XM Auxiliary Data Field (ADF) display can be
switched on or off. There is no ADF function for
the SIRIUS receiver.
switched on or off. There is no ADF function for
the SIRIUS receiver.
After carrying out steps 1 to 3 of “To display the
SETUP screen” (page 33), perform the operation
shown below.
SETUP screen” (page 33), perform the operation
shown below.
1
When the monitor is open, press and hold
MUTE/SETUP for at least 2 seconds. The
SETUP screen appears.
MUTE/SETUP for at least 2 seconds. The
SETUP screen appears.
2
Press preset 4 to activate the RADIO setting
mode. Press preset 4 again to select XM ADF.
mode. Press preset 4 again to select XM ADF.
3
Press g or f to select ON or OFF.
Select ON to display Auxiliary Data Field (ADF)
in the XM mode (refer to “Changing the Display”
on page 14).
in the XM mode (refer to “Changing the Display”
on page 14).
For any other settings, press preset 4 or another
preset button.
preset button.
4
After setting is completed, Press MUTE/SETUP
to return to normal mode.
to return to normal mode.
Subwoofer Control On and Off
After carrying out steps 1 to 3 of "To display the
SETUP screen" (page 33), perform the operation
shown below.
SETUP screen" (page 33), perform the operation
shown below.
1
When the monitor is open, press and hold
MUTE/SETUP for at least 2 seconds.
MUTE/SETUP for at least 2 seconds.
2
Press preset 5 to set to the SYSTEM setting
mode. Press preset 5 again to select the
SUBWOOFER mode.
mode. Press preset 5 again to select the
SUBWOOFER mode.
3
Press g or f to select Subwoofer ON or
OFF.
OFF.
For any other settings, press preset 5 or another
preset button.
preset button.
4
After setting is completed, press MUTE/SETUP
to return to normal mode.
to return to normal mode.
NOTES
• Initial mode is "SUBWOOFER ON."
• Set to "SUBWOOFER OFF" unless the subwoofer is
used.
• When the subwoofer is turned on, the subwoofer
output level can be adjusted. For more details, refer to
the Adjusting Volume/Balance/Fader (page 8).
the Adjusting Volume/Balance/Fader (page 8).
Adjusting Source Signal Levels
If the difference in volume level betweenFM radio
and other sources is too great, adjust the FM
signal level as follows.
and other sources is too great, adjust the FM
signal level as follows.
After carrying out steps 1 to 3 of “To display the
SETUP screen” (page 33), perform the operation
shown below.
SETUP screen” (page 33), perform the operation
shown below.
1
When the monitor is open, press and hold
MUTE/SETUP for at least 2 seconds. The
SETUP screen appears.
MUTE/SETUP for at least 2 seconds. The
SETUP screen appears.
2
Press preset 4 to select the RADIO setting
mode. Press preset 4 again to select FM
LEVEL.
mode. Press preset 4 again to select FM
LEVEL.
3
Press g or f to select the FM signal level
HIGH or LOW to make the signal levels between
the FM band and other sources closer.
HIGH or LOW to make the signal levels between
the FM band and other sources closer.
For any other settings, press preset 4 or another
preset button.
preset button.
4
After setting is completed, press MUTE/SETUP
to return to normal mode.
to return to normal mode.
MUTE/SETUP
g
g
g
g
g
f
f
f
f
f
Preset 4
Preset 5