Hitachi l26d204 ユーザーガイド

1

To turn on the TV, press POWER (POWER indicator on the front 

of the unit changes green. It may take approx. 10 seconds for a 

picture to appear on screen.). The starting setup function begins. 

Scan

Start

This unit has been preset to STORE brightness
This setting does not qualify under ENERGY 
STAR V4.0. To reduce brightness and energy 
consumption, change setting to ‘HOME’. This 
setting does qualify under ENERGY STAR V4.0.

TV Location

Store

Source

Cable

2

Press ▲/▼ to select “TV Location”, then press ◀/▶ to select 

“Home” or “Store”. This product qualifies for ENERGY STAR 

V4.0. in Home mode default setting.
NOTE:

This unit has been preset to Store brightness. This setting 

does not qualify under ENERGY STAR V4.0. To reduce 

brightness and energy consumption, change setting to 

‘Home’. This setting does qualify under ENERGY STAR V4.0.

The device may not conform to the ENERGY STAR V4.0. 

standard after Reset is performed or the Backlight is 

adjusted.

•

•

3

Press ▲ or ▼ to select “Source”, then press ◀ or ▶ to select 

“Cable” or “Air”.

4

Press ▲ or ▼ to select “Scan”, then press ▶ or ENTER. 

5

Now the “Auto Setup” starts. After the starting setup is 

completed, the TV channel appears on the screen.
• Depending on the reception condition, it may take from 15 

minutes to 30 minutes to complete memorizing digital cable 

channels. Please be patient.

If you press ENTER in the process of “Auto Setup”, the Starting 

Setup stops and changes to the normal screen.

When you make a menu selection, your changes occur 

immediately. You do not have to press EXIT to see your changes.

TV operation
1

To turn on the TV, press POWER.

(POWER indicator on the front of the unit changes green. 

It may take approx. 10 seconds for a picture to appear on 

screen.)

2

Adjust the volume level by pressing VOL + or – . The volume 

level will be indicated on the screen by blue bars. As the 

volume level increases, so do the number of bars. If the 

volume decreases, the number of blue bars also decreases.

3

Set the Signal Type option to the appropriate position (see 

“Air/Cable selection” on page 18).

4

Press the Direct Channel Selection (0-9, –) buttons to 

select the channel.

(If you press only channel number, channel selection will be 

delayed for a few seconds.)

•

•

1-9: 

Press 1-9 as needed. Example, to select channel 2, 

press 2, then press ENTER.

10-99: 

Press the 2 digits in order. Example, to select 

channel 12, press 1, 2, then press ENTER.

100-135:  Press the 3 digits in order. Example, to select 

channel 120, press 1, 2, 0, then press ENTER.

Press the first 1-3 digits, then press the – button, followed by 

the remaining number.

Example, to select channel 15-1, press 1, 5, –, 1, then press 

ENTER.

If a channel is selected with only audio content, “Audio 

Only” will be displayed on the screen.

If a channel is selected with a weak digital signal, “Weak 

Signal or Channel not available.” will be displayed on the 

screen.

The same program may be available on either an analog 

channel or a digital channel. You may choose to watch 

either format.

If a channel is selected to which you have not subscribed, 

“Digital channel is encrypted” will be displayed on the 

screen.

•

•

•

•

VHF

2-13

VHF

2-13

UHF

14-69

STD/HRC/IRC

14-36 (A) 

(W)

37-59 (AA) 

(WW)

60-85 (AAA) 

(ZZZ)

86-94 (86) 

(94)

95-99 (A-5) 

(A-1)

100-135 (100) 

(135)

01 (4A)

If a channel with no broadcast is selected, the sound will 

automatically be muted.

It may take a few seconds for a digital channel picture to appear 

on screen after being selected.

To view a signal from another device connected to your LCD TV, 

such as a VCR player, press INPUT, then press ▲/▼ or 

corresponding Number buttons (0-7), then press ENTER. You 

can select TV, Video 1, Video 2, Component, HDMI1, HDMI2, 

PC or DVD (Built-in) depending on which input jacks you used to 

connect your devices.

Press and release CH  / . The channel automatically stops at 

the next channel set into memory.

For proper operation, before selecting channels, they should be 

set into the memory. See “Memorizing channels” on page 18.

•

•

54H0321A_eng.indd   15

54H0321A_eng.indd   15

5/4/10   3:44:34 PM

5/4/10   3:44:34 PM