Newco gxdf-8d 操作ガイド
5
INSTALLATION INSTRUCTIONS (CONT’D)
4) Once you are satisfied with the by-pass %, you can begin calibrating the brew volume. Set the volume selector
switch to “I”. Depress the brew start/stop switch to resume brewing. After the brew cycle has finished check volume
of water in the container. Adjust the "brew time" with the control board located behind right side access plate. Turn
the dial clockwise to increase the volume of water and counterclockwise to decrease it. The “II” position on the
volume selector switch is automatically set to deliver twice the volume as the “I” position. As an alternate method for
setting brew time: Turn the timer adjustment clockwise to the maximum setting and initiate a brew cycle. When the
water level in the container is reached, slowly turn the timer adjustment counter clockwise until you hear the water
valve turn off. The timer is now set to deliver the volume of water. This Auto Cal feature allows you to streamline the
calibration process. The dial labeled “Visa” on the timer may be set for an additional amount of time to flash the brew
indicator on the face plate to allow time for the coffee to finish draining from the brew basket after the fill cycle has
completed. See Figure below for control board setting information.
of water in the container. Adjust the "brew time" with the control board located behind right side access plate. Turn
the dial clockwise to increase the volume of water and counterclockwise to decrease it. The “II” position on the
volume selector switch is automatically set to deliver twice the volume as the “I” position. As an alternate method for
setting brew time: Turn the timer adjustment clockwise to the maximum setting and initiate a brew cycle. When the
water level in the container is reached, slowly turn the timer adjustment counter clockwise until you hear the water
valve turn off. The timer is now set to deliver the volume of water. This Auto Cal feature allows you to streamline the
calibration process. The dial labeled “Visa” on the timer may be set for an additional amount of time to flash the brew
indicator on the face plate to allow time for the coffee to finish draining from the brew basket after the fill cycle has
completed. See Figure below for control board setting information.
5. Allow 10-15 minutes for the water in the tank to heat to brewing temperature. The heating light will go out when the
unit is up to temperature. Run one brew cycle to check for the proper temperature setting with an accurate
thermometer. Take the temperature of this water at a point below the brew basket opening, at the start of the brew
cycle and when the decanter is half full. Recommended temperature of the water is approximately 195 F. (Note:
Brew cycle may be canceled by depressing the brew start/stop switch). The brewer features an electronic
temperature control circuit and the temperature may be adjusted with the control board located behind the right side
access plate. See Figure below for control board setting information.
thermometer. Take the temperature of this water at a point below the brew basket opening, at the start of the brew
cycle and when the decanter is half full. Recommended temperature of the water is approximately 195 F. (Note:
Brew cycle may be canceled by depressing the brew start/stop switch). The brewer features an electronic
temperature control circuit and the temperature may be adjusted with the control board located behind the right side
access plate. See Figure below for control board setting information.
6. In higher altitude locations (5000 feet above sea level) the tank temperature may have to be adjusted lower to
prevent boiling. Turning adjustment knob in a clockwise direction will increase water temperature. This unit features
an electronic temperature control. Adjustment is located on the control board behind the right side access plate.
an electronic temperature control. Adjustment is located on the control board behind the right side access plate.
7. CAUTION: The water faucet will dispense hot water when the handle is pulled.
WARRANTY
Newco coffee brewers are warranted against defects in workmanship or materials, under normal use, for 90 days from
the date of purchase. Brewer parts are warranted against defect for 12 months from date of purchase.
Liability in all events is limited to the purchase price paid and liability under the aforesaid warranty is limited to replacing
or repairing any part or parts which are defective in material or workmanship, and returned to our factory, shipping cost
prepaid. No warranty expressed or implied, other than the aforesaid is made or authorized by Newco Enterprises, Inc.
Prompt disposition will be made if item proves to be defective, within warranty. Before returning any item, write or call
Newco, or the dealer, from whom the product was purchased, giving model number, serial number, and date of
purchase, and describe the nature of the defect. If damage was incurred during transit to you, file claim with the carrier