Frigidaire FRA054XT7 ユーザーガイド
6
Operating Instructions
Operating Instructions
(continued)
TO OPERATE ON FAN ONLY:
YOU WILL SEE:
Note: Use this function only when cooling is not
desired, such as for room air circulation or to exhaust
stale air on some models. (Remember to open the vent
during this function, but keep it closed during cooling
for maximum cooling efficiency.) You can choose any
fan speed you prefer. (Except “Auto Fan”).
During this function, the display will show the actual
room temperature, not the set temperature as in
the cooling mode.
desired, such as for room air circulation or to exhaust
stale air on some models. (Remember to open the vent
during this function, but keep it closed during cooling
for maximum cooling efficiency.) You can choose any
fan speed you prefer. (Except “Auto Fan”).
During this function, the display will show the actual
room temperature, not the set temperature as in
the cooling mode.
TO USE THE ENERGY SAVER
FEATURE:
FEATURE:
YOU WILL SEE:
TlMER: DELAY STOP / START
FEATURE
FEATURE
YOU WILL SEE HOW MUCH TIME IS CHOSEN:
DO THIS:
PRESS MODE
BUTTON
BUTTON
CHOOSE FAN
ONLY
ONLY
DO THIS:
PRESS MODE
BUTTON
BUTTON
CHOOSE
ENERGY SAVER
Note: In this mode, the fan will continue to run for 1
minute after the compressor shuts off. The fan then
cycles on for 20 seconds at 10 minute intervals until
the room temperature is above the set temperature,
at which time the compressor turns back on and
cooling starts.
minute after the compressor shuts off. The fan then
cycles on for 20 seconds at 10 minute intervals until
the room temperature is above the set temperature,
at which time the compressor turns back on and
cooling starts.
FIRST
DO THIS:
DO THIS:
PRESS
TIMER BUTTON
TIMER BUTTON
THEN
DO THIS:
DO THIS:
PRESS
UP/DOWN
SET BUTTONS
Note: For Delay Stop, the unit must be in the On position．
Note: For Delay Start, the unit must be in the Off position.
Note: For Delay Start, the unit must be in the Off position.
To adjust timer setting, tap or hold the UP arrow ( ) or
the DOWN arrow ( ) to change delay timer at 0.5 hour
increments, up to 10 hours, then at 1 hour increments up
to 24 hours. The control will count down the time remain-
ing until start (8, 7.5, 7, etc.). The Delay Start mode auto-
matically selects cooling with maximum Fan Speed. The
temperature maintained will be the same as previously set.
To change the set temperature, press "COOL" then Up or
Down arrows until the desired temperature is indicated on
the display. After 5 seconds, the control will automatically
change the display back to the hours remaining until the
unit will start/stop. Turning the unit "ON" or "OFF" at any
time will cancel the Delay Start/Stop function.
The Delay Start/Stop Feature will work until the unit either
starts or stops. Once that happens, the above steps have
to be repeated again.
the DOWN arrow ( ) to change delay timer at 0.5 hour
increments, up to 10 hours, then at 1 hour increments up
to 24 hours. The control will count down the time remain-
ing until start (8, 7.5, 7, etc.). The Delay Start mode auto-
matically selects cooling with maximum Fan Speed. The
temperature maintained will be the same as previously set.
To change the set temperature, press "COOL" then Up or
Down arrows until the desired temperature is indicated on
the display. After 5 seconds, the control will automatically
change the display back to the hours remaining until the
unit will start/stop. Turning the unit "ON" or "OFF" at any
time will cancel the Delay Start/Stop function.
The Delay Start/Stop Feature will work until the unit either
starts or stops. Once that happens, the above steps have
to be repeated again.
2009 Electrolux Home Products, Inc.
All rights reserved.