Frigidaire fas182p2a1 ユーザーガイド
Operation of Current
Device
Device
To reduce the risk of fire, electric shock, or injury to persons, read the
IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
WARNING
!
The power supply cord contains a current device that senses damage to the power cord. To
test your power supply cord do the following:
1. Plug in the Air Conditioner.
2. The power supply cord will have TWO buttons on the plug head. Press the TEST button.
You will notice a click as the RESET button pops out.
3. Press the RESET button. Again you will notice a click as the button engages.
4. The power supply cord is now supplying electricity to the unit. (On some products this is
also indicated by a light on the plug head).
test your power supply cord do the following:
1. Plug in the Air Conditioner.
2. The power supply cord will have TWO buttons on the plug head. Press the TEST button.
You will notice a click as the RESET button pops out.
3. Press the RESET button. Again you will notice a click as the button engages.
4. The power supply cord is now supplying electricity to the unit. (On some products this is
also indicated by a light on the plug head).
NOTES:
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is
Always make sure the RESET button is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is
pushed, or it cannot be reset. A new one can be obtained from the product manufacturer.
If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one
obtained from the product manufacturer.
To begin operating the air conditioner, follow these steps:
1. Set the thermostat to the highest number (coldest or cooler setting).
2. Set the selector control to the highest COOL setting.
3. Adjust the louvers for comfortable air flow (see Air Directional Louvers).
4. Once the room has cooled, adjust the thermostat to the setting you find most comfortable.
Review the “ Air Conditioner Features” section for other settings.
1. Set the thermostat to the highest number (coldest or cooler setting).
2. Set the selector control to the highest COOL setting.
3. Adjust the louvers for comfortable air flow (see Air Directional Louvers).
4. Once the room has cooled, adjust the thermostat to the setting you find most comfortable.
Review the “ Air Conditioner Features” section for other settings.
Using Air Conditioner
NOTE: If the air conditioner is turned
off, wait 3 minutes before restarting.
This allows pressure inside the
compressor and equalize. Failure to
follow these instructions may be
harmful to your unit.
off, wait 3 minutes before restarting.
This allows pressure inside the
compressor and equalize. Failure to
follow these instructions may be
harmful to your unit.
5
The controls featured in this manual are representative of many available models. Your
model may offer slightly different features.
model may offer slightly different features.
Cool Mode
The desired cool setting is selected by rotating the knob to the right to the appropriate
location.
“high cool” has maximum cooling effect and airflow.
“low cool” has minimum cooling effect and airflow.
“Mid cool” has the intermediate cooling effect and airflow.
Note: If your unit is equipped with a vent handle, keep it closed for maximum efficiency.
The desired cool setting is selected by rotating the knob to the right to the appropriate
location.
“high cool” has maximum cooling effect and airflow.
“low cool” has minimum cooling effect and airflow.
“Mid cool” has the intermediate cooling effect and airflow.
Note: If your unit is equipped with a vent handle, keep it closed for maximum efficiency.
Fan Mode
Rotate the knob to the left to select your choice of fan speeds for air circulation.
Note: When selecting a fan speed, the compressor will not run. On models with a vent
control, this mode can be used to remove stale air from the room, or to draw fresh air into the
room. Check the section 'Additional Things You Should Know'.
Rotate the knob to the left to select your choice of fan speeds for air circulation.
Note: When selecting a fan speed, the compressor will not run. On models with a vent
control, this mode can be used to remove stale air from the room, or to draw fresh air into the
room. Check the section 'Additional Things You Should Know'.
Thermostat
The thermostat is used to set the desired room temperature when the unit is being operated
in the “COOL MODE”.
To set the desired room temperature, rotate the thermostat switch to the desired setting.
After the set temperature is achieved the thermostat will automatically start and stop the
compressor in order to maintain the desired set temperature.
The thermostat is used to set the desired room temperature when the unit is being operated
in the “COOL MODE”.
To set the desired room temperature, rotate the thermostat switch to the desired setting.
After the set temperature is achieved the thermostat will automatically start and stop the
compressor in order to maintain the desired set temperature.
Rotate the thermostat selector clockwise for higher cool settings. Higher cool settings will
provide lower room temperature.
Rotate the thermostat selector counter clockwise for lower cool settings. Lower cool settings
will provide higher room temperature.
provide lower room temperature.
Rotate the thermostat selector counter clockwise for lower cool settings. Lower cool settings
will provide higher room temperature.
Air Conditioner
Features
Features
1
3
7
9