Frigidaire fcrs201rf ユーザーガイド
5
Insulation
The insulated space on this cabinet is sealed to maintain peak
efficiency. DO NOT drill holes in the cabinet. Holes drilled in the
cabinet may destroy that seal and damage electrical wiring
located in the insulated space. It may also pierce and damage
the sealed refrigeration system in the insulated space.
efficiency. DO NOT drill holes in the cabinet. Holes drilled in the
cabinet may destroy that seal and damage electrical wiring
located in the insulated space. It may also pierce and damage
the sealed refrigeration system in the insulated space.
DAMAGED ELECTRICAL WIRING OR WET INSULATION
CAUSED BY DRILLING WILL VOID THE WARRANTY.
CAUSED BY DRILLING WILL VOID THE WARRANTY.
Appliance Start-up
Once the appliance has been located in its permanent location
and the proper power and grounding has been provided, the
following items must be checked or completed:
and the proper power and grounding has been provided, the
following items must be checked or completed:
Cool Down Period
For safe food storage, allow 24 hours for the appliance to cool
down completely before loading with food. The appliance will
run continuously for the first several hours. Do not place any
food in the appliance until after the first 24 hours of operation.
down completely before loading with food. The appliance will
run continuously for the first several hours. Do not place any
food in the appliance until after the first 24 hours of operation.
Thermostat Setting
The appliance is shipped from the factory with the thermostat
set at about the mid-point of the operating range. Adjustments
colder or warmer can be made after the appliance has been
running for at least 8 hours. Allow at least 8 hours for temperature
stabilization before re-adjusting the thermostat.
set at about the mid-point of the operating range. Adjustments
colder or warmer can be made after the appliance has been
running for at least 8 hours. Allow at least 8 hours for temperature
stabilization before re-adjusting the thermostat.
Defrost Setting
The appliance is designed to defrost automatically every 12
hours. To set the time of defrost, wait until the desired time to
defrost. With the notch on the timer knob aligned with the line
on the bracket (Fig. A), turn the defrost timer knob clockwise
slowly. The timer will click several times, then once loudly, at
which point the defrost cycle begins. The timer knob will advance
through the defrost cycle, then click loudly at the end of the cycle
(Fig. B). The appliance will defrost automatically every 12 hours
after the first defrost cycle.
hours. To set the time of defrost, wait until the desired time to
defrost. With the notch on the timer knob aligned with the line
on the bracket (Fig. A), turn the defrost timer knob clockwise
slowly. The timer will click several times, then once loudly, at
which point the defrost cycle begins. The timer knob will advance
through the defrost cycle, then click loudly at the end of the cycle
(Fig. B). The appliance will defrost automatically every 12 hours
after the first defrost cycle.
Features
NSF and FDA Approved Adjustable Shelving
This appliance is provided with NSF and FDA approved heavy
duty epoxy powder coated adjustable shelves. The one with the
wires that are angled on the front and back goes on the floor of
the cabinet. The others are placed in the adjustable stainless
steel shelf supports that clip into the shelf support strips on each
side of the interior. Make sure to place the shallow shelf in the
upper-most position.
duty epoxy powder coated adjustable shelves. The one with the
wires that are angled on the front and back goes on the floor of
the cabinet. The others are placed in the adjustable stainless
steel shelf supports that clip into the shelf support strips on each
side of the interior. Make sure to place the shallow shelf in the
upper-most position.
Front Fixed and Rear Swivel Casters
This appliance comes with two (2) front fixed casters with brakes
and two (2) rear swivel casters. The casters allow the appliance
to be moved with ease and then locked in position at its desired
location.
and two (2) rear swivel casters. The casters allow the appliance
to be moved with ease and then locked in position at its desired
location.
Fig. A
Position of knob before
turning clockwise to start
defrost cycle (First click)
Fig. B
Position of knob at end
of defrost cycle (Second
click)