Frigidaire frt22rrhw1 ユーザーガイド

ページ / 18
9
Reversible Door
Instructions 
(continued)
G05I0118
7. 
Reverse 
handles 
while 
doors 
are 
off. 
Remove 
the 
two 
screws
attaching 
the 
handle 
to 
the 
bottom 
of 
the 
freezer 
door. 
Remove
short 
trim 
piece 
by 
sliding 
the 
trim 
straight 
up 
and 
off 
of 
handle
bracket. 
Remove 
the 
screw 
attaching 
the 
top 
of 
the 
handle 
to 
door,
and 
reinstall 
on 
other 
side, 
using 
the 
hole 
found 
behind 
the 
 
self-
adhesive 
nameplate. 
To 
move 
nameplate 
to 
the 
other 
side, 
peel
off 
the 
nameplate 
and 
reapply 
over 
the 
old 
handle 
holes. 
 
Reattach
handle 
to 
bottom 
of 
door. 
Slide 
the 
trim 
piece 
straight 
down 
onto
handle 
bracket.
Freezer 
Door
G05I0111
Refrigerator 
Door
8. 
 Trim Removal (Full-Length Trim models only)
In 
some 
models, 
the 
refrigerator 
door 
has 
full 
length 
trim
piece 
which 
continues 
from 
the 
bottom 
of 
the 
handle 
to 
the
bottom 
of 
the 
door. 
The 
top 
of 
the 
trim 
attaches 
to 
the 
handle
bracket. 
An 
adhesive 
"trim 
lock" 
is 
positioned 
about 
half-
way 
down. 
The 
bottom 
of 
the 
trim 
is 
held 
in 
place 
by 
either
an 
adhesive 
trim 
lock, 
or 
trim 
lock 
with 
two 
prongs 
inserted
into 
hole 
on 
the 
face 
of 
the 
door. 
Remove 
the 
trim 
by 
gently
pulling 
the 
trim 
lock 
areas 
out 
and 
away 
from 
the 
door. 
When
the 
trim 
is 
free 
from 
the 
door, 
slide 
the 
trim 
straight 
down 
and
away 
from 
the 
handle 
bracket.
For 
models 
with 
short 
handle 
trim, 
remove 
by 
sliding 
the
trim 
straight 
down 
and 
off 
of 
handle 
bracket.
To 
remove 
handles: 
Remove 
the 
three 
screws 
attaching 
the
handle 
to 
the 
refrigerator 
door. 
Carefully 
remove 
hole 
plugs
from corresponding holes on 
opposite side of 
doors and
reattach 
handle.
To 
reattach 
trim: 
Slide 
both 
trim 
locks 
out 
of 
trim. 
Insert 
the
new 
adhesive 
trim 
locks 
contained 
in 
your 
literature 
pack.
NOTE: 
 
Trim 
lock 
must 
be 
removed 
and 
installed 
by 
sliding
OVER 
the 
two 
donut 
shaped 
areas. 
Install 
trim 
to 
handle 
by
sliding 
up 
over 
bottom 
of 
handle. 
Carefully 
align 
trim 
and
press 
down 
at 
trim 
lock 
locations. 
Replace 
hole 
plug 
on
opposite 
side. 
Use 
rubbing 
alcohol 
to 
remove 
any 
adhesive
residue 
from 
old 
trim 
lock 
location(s).
For 
models 
with 
short 
handle 
trim
slide 
the 
trim 
straight 
up
onto 
handle 
bracket.