Microtek 1800f 補足マニュアル
2
(English)
7.
Next, select the Interrupt/Request option, click
Change Setting, and use the Up/Down arrow
keys to select different IRQ number. If all IRQs
are taken, you need to contact your dealer or
computer manufacturer to help on how to free
up an IRQ in this range.
Change Setting, and use the Up/Down arrow
keys to select different IRQ number. If all IRQs
are taken, you need to contact your dealer or
computer manufacturer to help on how to free
up an IRQ in this range.
8.
When all the settings are correct, click OK
OK
OK
OK
OK to
save the modifications. The dialog box should
now show the correct Interrupt Request and
Input/Output address settings. If you’re asked
to shut down your computer, select No
now show the correct Interrupt Request and
Input/Output address settings. If you’re asked
to shut down your computer, select No
No
No
No
No, then
click Close
Close
Close
Close
Close. You will be asked whether you wish
to restart your computer. Click Y
Y
Y
Y
Yes
es
es
es
es and restart
your computer.
Q3: My SCSI card is detected by Windows 98, but
the scanner cannot be found in Scanner Test
utility.
utility.
A3:
A3:
A3:
A3:
A3: Follow the steps below:
a)
In Windows, choose Start, then Shut Down to
turn off computer power. Then turn off the
power of your scanner.
turn off computer power. Then turn off the
power of your scanner.
b)
Check to make sure you have connected the
correct SCSI cable to the SCSI port, not the
parallel port. If you connect the SCSI cable to
the parallel port, your scanner will not be
found.
correct SCSI cable to the SCSI port, not the
parallel port. If you connect the SCSI cable to
the parallel port, your scanner will not be
found.
If conflicts
happen, the
message
shows here.
Currently no
conflicts
happen.
happen, the
message
shows here.
Currently no
conflicts
happen.
c)
If your scanner has a SCSI terminator switch,
switch it to the On position. If the scanner
doesn’t have a SCSI terminator switch, plug the
SCSI terminator on the SCSI port.
switch it to the On position. If the scanner
doesn’t have a SCSI terminator switch, plug the
SCSI terminator on the SCSI port.
d)
If your scanner is chained to other SCSI device,
the SCSI ID of the SCSI device should not be set
to the same ID number. By default, Microtek’s
scanner SCSI ID is 6.
the SCSI ID of the SCSI device should not be set
to the same ID number. By default, Microtek’s
scanner SCSI ID is 6.
e)
Turn on your scanner power, then restart your
computer.
computer.
Q4: My Microtek scanner came with dual
interface -- USB and SCSI. Can I connect both
interface?
interface?
A4:
A4:
A4:
A4:
A4: When connecting dual interface scanner to
computer, you should choose either USB or
SCSI, not both.
SCSI, not both.
If SCSI interface is chosen, the terminator has
to be connected to finish a complete connec-
tion. Depending on different configurations,
you may require 25-pin SCSI terminator. If USB
to be connected to finish a complete connec-
tion. Depending on different configurations,
you may require 25-pin SCSI terminator. If USB
If USB
If USB
If USB
If USB
is chosen, the SCSI cable along with the
is chosen, the SCSI cable along with the
is chosen, the SCSI cable along with the
is chosen, the SCSI cable along with the
is chosen, the SCSI cable along with the
terminator should all be removed.
terminator should all be removed.
terminator should all be removed.
terminator should all be removed.
terminator should all be removed.
terminator should all be removed.
Q5: What’s the recommended power up se-
quence?
A5:
A5:
A5:
A5:
A5: When using SCSI interface, be sure you have
connected the SCSI cable and the terminator
first, then connect the DC power adapter.
first, then connect the DC power adapter.
Q6: I have followed the above instructions, but
still cannot fix the problem.
A6:
A6:
A6:
A6:
A6: Visit the web site of the SCSI card provider
(e.g., Adpatec or AdvanSys)