Microtek 3700 インストール手順
7
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, (example - use only shielded interface cables
when connecting to computer or peripheral devices). Any changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
when connecting to computer or peripheral devices). Any changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Responsible Party:
Loi Han
3715 Doolittle Drive
Redondo Beach, CA 90278-1226
U.S.A.
3715 Doolittle Drive
Redondo Beach, CA 90278-1226
U.S.A.
Telephone No:
1-310-297-5000
Federal Communications Commission Interference Statement
This equipment (Model: MRS-2400TPFU) has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Note: 1) A shielded of USB interface cable with ferrite core installed on the scanner connector
end must be used with this equipment. 2) AC adapter with ferrite core installed on the
scanner connector end must be used with this equipment.
end must be used with this equipment. 2) AC adapter with ferrite core installed on the
scanner connector end must be used with this equipment.
CAUTION
Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user's authority to operate the equipment.
compliance could void the user's authority to operate the equipment.
Trade Name
Model Number
ScanMaker 8700
MRS-2400TPFU
Tested to Comply
With FCC Standards
Tested to Comply
With FCC Standards
FOR HOME OR OFFICE USE
7. Reading the
documentation
For PC users
1. Insert the Microtek CD-ROM into your CD-ROM
drive.
2. When the Microtek Software Installer comes up on
your screen, click the View Manual button that
corresponds to the manual you wish to read. This will
launch Adobe Acrobat Reader, and you can then read or
print the manual.
corresponds to the manual you wish to read. This will
launch Adobe Acrobat Reader, and you can then read or
print the manual.
For Macintosh users
1. Insert the Microtek CD-ROM into your CD-ROM
drive.
2. Launch the Adobe Acrobat Reader program. From the
File menu, choose the Open command, and open the
file for the manual that you wish to view; manuals have
a .pdf extension to their file name. The manual is then
ready to be viewed or printed.
file for the manual that you wish to view; manuals have
a .pdf extension to their file name. The manual is then
ready to be viewed or printed.
8. Troubleshooting
If you encounter problems with the installation, see the
troubleshooting file in the Techinfo folder on your Microtek
CD-ROM.
troubleshooting file in the Techinfo folder on your Microtek
CD-ROM.