Lowrance m52 s 操作ガイド
81
GPS Quick Reference
Start outdoors, with a clear view of the open sky. As you practice, try
navigating to a location at least a few blocks away. While you're learning,
navigation in too small an area will constantly trigger arrival alarms.
navigating to a location at least a few blocks away. While you're learning,
navigation in too small an area will constantly trigger arrival alarms.
1. Install the unit. (See complete installation details beginning on page 9.)
2. To turn on the M52, press and release
PWR
key.
3. Opening screen displays the GPS plotter at the 4,000 mile zoom
range. Rotate through the four main GPS Page screens (Plotter, Satel-
lite Status, Navigation and Position Page) by pressing
range. Rotate through the four main GPS Page screens (Plotter, Satel-
lite Status, Navigation and Position Page) by pressing
PAGES
|
← to
GPS
|
↓ or ↑ to select Page Name|
EXIT
. Switch Pages to display Satellite
Status Page.
4. Wait while unit locates satellites and calculates current position. Process
is visible on Satellite Page. This takes an average of 1 minute or less under
clear sky conditions (unobstructed by terrain or structures). When the unit
acquires position, a tone sounds and a position acquired message appears.
is visible on Satellite Page. This takes an average of 1 minute or less under
clear sky conditions (unobstructed by terrain or structures). When the unit
acquires position, a tone sounds and a position acquired message appears.
5. With position acquired, press
PAGES
key to display Plotter Page, which
shows your position in the center. You can move around the plotter by:
Zoom in closer to see greater detail: press
ZIN
(zoom in key.)
Zoom out to see more area, less detail: press
ZOUT
(zoom out key.)
Scroll display north, south, east or west using arrow keys ↑ ↓ → ←.
To stop scrolling and return to current position, press
EXIT
key.
6. Set a waypoint (Wpt 001) at your current position so you can navi-
gate back here: press
gate back here: press
WPT
|
WPT
. Waypoint symbol and "001" appears.
7. If you've already made some waypoints or event marker icons,
zoom/scroll to find a nearby location to go to. Otherwise, travel around
some and place some waypoint at place of interest. When you have sev-
eral in place, use arrow keys to center cursor cross-hair over one of your
existing waypoint or locations.
zoom/scroll to find a nearby location to go to. Otherwise, travel around
some and place some waypoint at place of interest. When you have sev-
eral in place, use arrow keys to center cursor cross-hair over one of your
existing waypoint or locations.
8. Navigate to selected destination: press
MENU
|
ENT
|
EXIT
. Follow dotted
course line on Plotter Page or compass bearing arrow on Navigation Page.
9. At destination, Arrival Alarm goes off; to clear it, press
EXIT
. Cancel
navigation: press
MENU
|
MENU
|
↓ to
C
ANCEL
N
AVIGATION
|
ENT
|
←
to Y
ES
|
ENT
.
10. Return to Wpt 1 by Backtrack Trail. Press
MENU
|
MENU
|
↓ to
M
Y
T
RAILS
|
ENT
. Press
↓ to Trail 1|
ENT
|
↓ to
N
AVIGATE
|
ENT
|
→ to
R
E-
VERSE
|
ENT
|
← to
N
AVIGATE
|
ENT
. (If arrival alarm sounds, press
EXIT
.)
Follow navigation displays.
11. Back home, Arrival Alarm goes off; press
EXIT
. Cancel navigation:
press
MENU
|
MENU
|
↓ to
C
ANCEL
N
AVIGATION
|
ENT
|
←
to Y
ES
|
ENT
.
12. To turn off the unit, press and hold
PWR
key for three seconds.