Campbell Hausfeld ce7003 30 gallon truck mounted air compressor w ユーザーガイド

Motors, electrical equipment

and controls can cause electrical

arcs that will ignite a flammable gas or vapor. Never
operate or repair in or near a flammable gas or vapor.
Never store flammable liquids or gases in the vicinity of the
compressor.

Never operate compressor without

Carbon monoxide can cause severe

nausea, fainting or death. Do not operate unit inside a
poorly ventilated area.

Never operate compressor without

a beltguard. This unit can start

automatically without warning. Personal injury or
property damage could occur from contact with moving
parts.

◆

Do not wear loose clothing or jewelry that will get caught in

the moving parts of the unit�

Compressor parts may be hot even if

the unit is stopped.

◆

Keep fingers away from a running compressor;

fast moving and hot parts will cause injury
and/or burns�

◆

If the equipment should start to vibrate abnormally, STOP

the engine/motor and check immediately for the cause�
Vibration is generally an indication of trouble.

NEVER refuel a running or hot

engine. Explosive fuel can cause fires

and severe burns. Avoid overfilling fuel tank.

◆

Check fuel level before starting the engine� Wipe

off any spilled gas before starting the engine�

Gasoline vapor is highly flammable. Refill

outdoors or only in well ventilated areas. Do

not store, spill or use gasoline near an open flame or heat devices such
as a stove, furnace, or water heater, which utilize a pilot light, or any
device that can create a spark. If gasoline is accidentally spilled, move
unit away from the spill area and avoid creating any source of ignition
until gasoline vapors have dissipated.

◆

To reduce fire hazard, keep engine/motor exterior free of oil,

solvent, or excessive grease�

This compressor is equipped with an ASME

code safety valve with a pressure setting of 200

psi for two-stage compressors or 150 psi for single-stage compressors.
Should this ASME code safety valve require replacement, the
replacement valve must have the same flow and pressure ratings as the
original valve to protect the pressurized components from bursting.
The flow and pressure ratings can be found on the valve. NEVER
REMOVE AND REPLACE THIS SAFETY VALVE WITH A PLUG. The safety
valve in the intercooler of a two-stage compressor does not provide
system protection.

Maximum operating pressure is 175 psi for

two-stage compressors and 125 psi for single

stage compressors. Do not operate with pressure switch or pilot valves
set higher than 175 psi (two-stage) or 125 psi (single stage).

◆

Never attempt to adjust ASME safety valve. Keep safety valve

free from paint and other accumulations�

◆

Do not tamper with governor setting on engine�

Overspeeding the unit severely shortens engine life and may
also be very hazardous�

Never attempt to repair or modify

a tank! Welding, drilling or any

other modification will weaken the tank resulting in
damage from rupture or explosion. Always replace worn,
cracked or damaged tanks.

Drain liquid from tank daily.

◆

Tanks rust from moisture build-up, which weakens the tank�

Make sure to drain tank regularly and inspect periodically for
unsafe conditions such as rust formation and corrosion�

◆

Fast moving air will stir up dust and debris which may be

harmful. Release air slowly when draining moisture or
depressurizing the compressor system�

◆

STOP the engine whenever leaving the work area, before

cleaning, making repairs or inspections� When cleaning,
repairing or inspecting, make certain all moving parts have
stopped� Disconnect the spark plug wire and keep the wire
away from the plug to prevent accidental starting�

Spraying preCautionS

Do not spray flammable materials

in vicinity of open flame or near

ignition sources including the compressor unit.

◆

Do not smoke when spraying paint, insecticides,

or other flammable substances�

◆

Use a face mask/respirator when spraying and

spray in a well ventilated area to prevent health
and fire hazards�

◆

Do not direct paint or other sprayed material at

the compressor� Locate compressor as far away
from the spraying area as possible to minimize overspray
accumulation on the compressor�

◆

When spraying or cleaning with solvents or toxic

chemicals, follow the instructions provided by the chemical
manufacturer�

Save tHeSe inStruCtionS

do not diSCard

The DANGER, WARNING, CAUTION, and NOTICE
notifications and instructions in this manual cannot
cover all possible conditions and situations that may
occur� It must be understood by the operator that
caution is a factor which cannot be built into this
product, but must be supplied by the operator�

Models CE7002, CE7003, CE7004

Important Safety Information (Continued)