Jobsite lsc-6s ユーザーガイド
3
9. Tightly twist the end of each wire until no
frayed ends remain.
10. Attach the speaker wires to the speaker
terminal connectors. Connect the
negative output from the amplifier to the
black terminal and the positive output to
the red terminal.
negative output from the amplifier to the
black terminal and the positive output to
the red terminal.
11. There are four clamps “dogs” which
hold each speaker in place. Rotate all
the dogs inward.
the dogs inward.
12. Insert the loudspeaker into the cutout in
the ceiling.
13. The dogs are tightened via four
front-baffle screws. Tighten the dogs
by turning the screws clockwise,
while pressing the loudspeaker against
the ceiling. NOTE: DO NOT OVER
TIGHTEN THESE SCREWS. Over-
tightening the screws may make the
grille difficult to install.
by turning the screws clockwise,
while pressing the loudspeaker against
the ceiling. NOTE: DO NOT OVER
TIGHTEN THESE SCREWS. Over-
tightening the screws may make the
grille difficult to install.
14. Install the grille into the speaker.
Installation New Construction:
Install the proper ceiling bracket for this
loudspeaker (NCB-6) using the instructions
supplied with the bracket. After the hole is
cut in the drywall per the bracket
instructions, perform the following steps:
loudspeaker (NCB-6) using the instructions
supplied with the bracket. After the hole is
cut in the drywall per the bracket
instructions, perform the following steps:
1. Strip 1/4" of insulation from the end of
each wire coming from the amplifier.
2. Tightly twist the end of each wire until no
frayed ends remain.
3. Attach the speaker wires to the speaker
terminal connectors. Connect the
negative output from the amplifier to the
black terminal and the positive output
from the amplifier to the red terminal.
negative output from the amplifier to the
black terminal and the positive output
from the amplifier to the red terminal.
4. There are four clamps “dogs” which
hold each speaker in place. Rotate all
the dogs inward.
the dogs inward.
5. Insert the loudspeaker into the cutout in
the ceiling.
6. The dogs are tightened via four
front-baffle screws. Tighten the dogs
by turning the screws clockwise,
while pressing the loudspeaker against
the ceiling. NOTE: DO NOT OVER
TIGHTEN THESE SCREWS. Over-
tightening the screws may make the grille
difficult to install.
by turning the screws clockwise,
while pressing the loudspeaker against
the ceiling. NOTE: DO NOT OVER
TIGHTEN THESE SCREWS. Over-
tightening the screws may make the grille
difficult to install.
8. Install the grille into the speaker.
Removing the Grilles:
To remove the grille from the LSC-6S, obtain
a small paper clip (size #1, common) and
bend the last quarter inch of it into an “L”
shape. Holding the paper clip with a pair of
pliers, insert the end with the “L” into a hole
near the edge of the grille. Stay near the
edge of the grille. Remove the grille by
pulling the paper clip towards you.
a small paper clip (size #1, common) and
bend the last quarter inch of it into an “L”
shape. Holding the paper clip with a pair of
pliers, insert the end with the “L” into a hole
near the edge of the grille. Stay near the
edge of the grille. Remove the grille by
pulling the paper clip towards you.
Painting the Speakers
The speakers must be masked prior to
painting them. The inside circular portion of
the hole template can be used as a paint
mask. Remove the outside portion of the
template by gently pulling along the
perforation. Affix the mask to the front of the
speaker using a piece of tape. Fold the tape
onto itself to form a double-sided loop. Affix
the tape to the tweeter and place the mask
onto the speaker.
painting them. The inside circular portion of
the hole template can be used as a paint
mask. Remove the outside portion of the
template by gently pulling along the
perforation. Affix the mask to the front of the
speaker using a piece of tape. Fold the tape
onto itself to form a double-sided loop. Affix
the tape to the tweeter and place the mask
onto the speaker.
DS00385ACN_LSC-6S.qxp 11/18/04 7:17 PM Page 3