Panasonic PV-GS9 ユーザーズマニュアル
Before using
15
LSQT1284
ª
How to turn the power on and off with
the LCD monitor/viewfinder
the LCD monitor/viewfinder
When the mode dial is set to Tape Recording
Mode, the power can be turned on and off with
the LCD monitor and the viewfinder.
Mode, the power can be turned on and off with
the LCD monitor and the viewfinder.
1
Open the LCD monitor out or extend the
viewfinder to turn on the power. (
viewfinder to turn on the power. (
-16-
)
≥The LCD monitor or viewfinder will be
activated.
2
Close the LCD monitor and retract the
viewfinder to turn off the power.
viewfinder to turn off the power.
≥The power will not turn off unless the LCD
monitor is closed and the viewfinder is
retracted.
retracted.
≥The Status indicator automatically goes off
and the power turns off. (If quick start is set to
[ON] (
[ON] (
-17-
), the unit goes into quick start
standby mode and the Status indicator lights
green.)
green.)
≥The power does not turn off even if the
LCD monitor is closed and the viewfinder
is retracted while recording on a tape.
is retracted while recording on a tape.
3
Open the LCD monitor or extend the
viewfinder to turn the power on and use the
Camcorder again.
viewfinder to turn the power on and use the
Camcorder again.
≥The Status indicator lights red and the power
turns on.
Setting date and time
When the Camcorder is turned on for the first
time, [SET DATE AND TIME] will appear.
time, [SET DATE AND TIME] will appear.
≥Select [YES] and press the center of the
joystick. Perform steps 2 and 3 below to set the
date/time.
date/time.
≥Set to Tape Recording Mode.
1
Set [BASIC] >> [CLOCK SET] >> [YES]. (
-20-
)
2
Move the joystick left or right in order to
select the item to be set. Then move the
joystick up or down to set the desired value.
≥The year will change as follows:
select the item to be set. Then move the
joystick up or down to set the desired value.
≥The year will change as follows:
2000, 2001, ..., 2089, 2000, ...
≥The 12-hour clock is used.
3
Press the joystick to determine the setting.
≥The clock function starts at [00] seconds.
≥The clock function starts at [00] seconds.
ª
About date/time
≥The date and time function are driven by a built-
in lithium battery.
≥Make sure to check the time before recording
because the built-in clock is not very accurate.
ª
Recharging the built-in lithium battery
≥If [
0] or [--] appears when the Camcorder is
turned on, then the built-in lithium battery needs
to be charged. Use the steps below to charge
the battery.
Connect the AC adaptor to the Camcorder or
attach the battery to the Camcorder, and the
built-in lithium battery will be recharged. Leave
the Camcorder as is for approx. 24 hours, and
the battery will drive the date and time for
approx. 6 months. (The battery is still being
recharged even if the mode dial is set to OFF.)
to be charged. Use the steps below to charge
the battery.
Connect the AC adaptor to the Camcorder or
attach the battery to the Camcorder, and the
built-in lithium battery will be recharged. Leave
the Camcorder as is for approx. 24 hours, and
the battery will drive the date and time for
approx. 6 months. (The battery is still being
recharged even if the mode dial is set to OFF.)
≥When turning on the power for the first time after
charging, [SET DATE AND TIME] will appear.
Select [YES] and set the date and time.
Select [YES] and set the date and time.
Set the mode dial to OFF when this unit is
not being used.
not being used.
PV-GS90P_LSQT1284_Eng.book 15 ページ ２００７年１１月２８日 水曜日 午前９時２０分