Freestyle fs81239 ユーザーガイド

TRIM

BOILER

Boiler IMS V1 01-12-2008

automatically set in accordance with

the date. The date can be set within

the range of 1 January 2000 to 31

December 2099.

TO SET THE ALARM TIME

1. Press S3 button to select ALARM

mode.

2. Press and hold S2 button for

around 3 seconds, the minute digits

will blink.

3. Press S1 button to set the minute

digits. Holding down the button will

speed up the process.

4. Press S3 button, the hour digits

will blink.

5. Press S1 button to set the hour

digits.

6. After finished making all the

settings, press S2 button to

confirm.

NOTE: The alarm will automatically

be activated after being set.

TO USE THE ALARM AND HOURLY

CHIME

In ALARM mode,

1. Press S1 button once to activate

the daily alarm. Alarm indicator

will appear.

2. Press again to activate the hourly

chime. Chime indicator will

appear.

3. Press a third time to activate both

functions. Both of the indicators

will appear.

4. Press a fourth time to deactivate

both functions. Both of the

indicators will disappear.

WHEN AN ALARM OR HOURLY CHIME

GOES OFF

A tune will go off by the hour if the

hourly chime function is activated.

A 10-second alarm tune will be emitted

at the designated time when the alarm

is activated. To stop the tune, press

any button.

TO USE THE CHRONOGRAPH

1. Press S3 button to select

CHRONOGRAPH mode.

2. The chronograph will then be

displayed in its current state –

reset, running, or stopped.

3. To resume a counting, press S1

button to resume from where it left

off.

4. To start a new counting, reset the

stop watch to zero first.

Press S1 button to stop counting,

then press S2 button to reset the

counter to zero

For the measurement of elapsed time:

In CHRONOGRAPH mode,

1. Press S1 button to start counting.

2. To stop counting, press S1 button.

Press S1 button again to resume

from where it left off.

3. To reset to zero, press S1 button to

stop counting and then press S2

button.

For the measurement of split time:

Model FS81239

Model FS81240

S1 – Start Button

S2 – Reset Button

S3 – Mode Button

S4 – Light Button

DISPLAY MODES

The watch has five display modes:

NORMAL TIME, ALARM (AL),

CHRONOGRAPH (ST), DUAL TIME (T2)

and TIMER (TR).

To change from one display mode to

another, press S3 button once.

NOTE: In any setting mode, if there is

no manipulation for around 1 minute,

the watch will automatically save the

entered data and exit the setting

procedure.

TO SET THE TIME AND CALENDAR

1. Press S3 button to select NORMAL

TIME mode.

2. Press S1 button to toggle between

12-hour and 24-hour format.

3. Press and hold S2 button for

around 3 seconds, the second digits

will blink

4. Press S1 button to reset second

digits to 00. This will increase the

time by 1 minute if the original

setting is at 30 to 59 seconds.

5. Press S3 button, the minute digits

will blink

6. Press S1 button to set the minute

digits. Holding down the button will

speed up the process.

7. Press S3 button, the hour digits

will blink

8. Press S1 button to set the hour

digits.

9. Follow the same pattern to set the

month, date and year.

10.After finished making all the

settings, press S2 button to

confirm.

NOTE: The day (of the week) is

In CHRONOGRAPH mode,

1. Press S1 button to start counting.

2. While the chronograph is running,

press S2 button to register a lap.

The chronograph is still running in

the background.

To display the currently accumu-

lated time, press S2 button

again.

3. Repeat the last step until all the

laps have been registered.

4. To stop counting, press S1 button.

Press S1 button again to resume

from where it left off.

5. To reset to zero, press S1 button to

stop counting, then press S2 button

to reset the counter to zero.

For the measurement of two finishes:

In CHRONOGRAPH mode,

1. Press S1 button once to start

counting.

2. While the chronograph is running,

press S2 button once to register

and display the time of the first

runner. The chronograph is still

running in the background.

3. Press S1 button to stop and register

the time of the second runner.

4. Press S2 button to display the time

of the second runner.

5. To reset to zero, press S2 button

again.

NOTE: You can leave the chronograph

running while switching over to other

operating modes.

TO SET THE DUAL TIME

1. Press S3 button to select DUAL

TIME mode.

2. Press and hold S2 button for

around 3 seconds, the hour digits

will blink.

3. Press S1 button to set the hour

digits. Holding down the button

will speed up the process.

4. After finishing making the setting,

press S2 button to confirm.

NOTE: In DUAL TIME settings, only the

hour digits are open to setting. The

value of the minute digits and second

digits will be the same as that of

NORMAL TIME.

TO SET THE TIMER

1. Press S3 button to select TIMER

mode.

2. Press and hold S2 button for

around 3 seconds, the second digits

will blink.

3. Press S1 button to set the second

digits. Holding down the button will

speed up the process.

4. Press S3 button, the minute digits

will blink.

5. Press S1 button to set the minute

digits.

6. Press S3 button, the hour digits

will blink.

7. Press S1 button to set the hour

digits.

8. After finished making all the

settings, press S2 button to

confirm.

TO USE THE TIMER

In TIMER mode,

1. Press S1 button to start counting.

2. To stop counting, press S1 button.

Press S1 button again to resume

from where it left off.

3. After reaching zero in a countdown,

a 10-second tune will be emitted.

To stop the tune, press any button.

4. The timer will reload automatically

when the tune stops.

TO USE THE BACKLIGHT

Press S4 button to turn on the

backlight for around 3 seconds.

SOLAR CELL

This watch uses a solar cell (Maxell

ML1220) that is recharged from solar

energy by simply exposing the watch

face to external light sources. As with

other rechargeable batteries, when

the solar cell loses its ability to achieve

full charge, replace the battery with a

Maxell ML1220 rechargeable battery.

NOTE: After replacing the battery, all

data stored in watch memory will be

erased. Thus, there is a need to reset

the desired time of the watch.

The table below shows the recharge-

able battery power indicator status:

NOTES:

• From a fully charged battery (Level

1), if the watch is stored in a dark

place or is without any light

exposure for a period of around 5

months, the battery will drain

completely. The battery then needs

to be recharged immediately up to

Level 3 to be able to reset the watch

functions manually. This will

usually take about 5 hours.

• Leaving the watch in direct sunlight

or another strong light source can

cause the battery power indicator

to temporarily show a reading that

may be higher than the actual

battery level. By pressing the S4

button (Light Button) momentarily,

actual battery power level will be

displayed.

• From a Full Charge battery

condition, normal watch functions

are expected to last for a period of

12 months.

Exposing the watch to a light source

for the periods shown below each day

restores the power used during normal

operating conditions:

CHARGING CONDITIONS

NOTES:

• Stable watch operation is achieved

through frequent battery recharging.

• Under certain conditions of

charging, the watch can become

very hot. Avoid leaving the watch

under the following conditions

during battery recharging and be

extra cautious when handling the

watch:

– On the dashboard of a car

under direct sunlight

– Too close to an incandescent

lamp

• If the watch is overly hot, the display

will be blank. It will return to

normal when the ambient

operating temperature is achieved.

The table below shows the amount of

light exposures and the corresponding

charging duration to enhance the

battery power from lower to higher

levels:

NOTE: All of the above exposure time

values are for reference only. Actual

exposure time depends on lighting

conditions.

POWER SAVING FUNCTION

The watch will turn into Sleep Mode

(blank display) when it is placed in the

dark or exposed to light below 5 Lux

intensity within 15 seconds. Depending

on the Battery Level status when the

watch is at Sleep Mode, the watch still

keeps time up to Battery Level 3. When

the watch is exposed to ambient light

of above 5 Lux, the display of the watch

will automatically return to normal

mode within a period of 5 seconds.

The display can also return to normal

immediately as soon as any button is

activated or pressed.

Level

Battery

power

indicator

Function

Status

All functions are

enabled.(power

saving function)

Alarm, hourly time

signal, button signal

and backlight are

disabled. (power

saving function)

Time keeping

functions are still

enabled, the screen

display will turn into

sleep power saving

mode after flashing

for 30 seconds. Press

any button, the screen

display will flash

again for 30 seconds

to alert you to charge

the battery.

All functions are

disabled. Need to

recharge or replace

the battery immedia-

tely if it cannot be

recharged.

NO DISPLAY

Exposure Level

(Brightness)

Outdoor Sunlight

(50,000 Lux)

Sunlight through a

window (10,000 Lux)

Daylight through a

window on a Cloudy

Day (5,000 Lux)

Indoor fluorescent

lighting (500 Lux)

Approximate

Exposure Time

10 minutes

48 minutes

1.5 hours

16 hours

To reduce carbon foot print, these

Freestyle instructions are printed with

soy inks on recycled paper.

FS-812-1050-01

Exposure

Level

(Brightness)

Outdoor

Sunlight

(50,000 Lux)

Sunlight

through a

window

(10,000 Lux)

Daylight

through a

window on a

Cloudy Day

(5,000 Lux)

Indoor

fluorescent

lighting

(500 Lux)

Level 4

minutes

hours

Level 3

minutes

hours

Level 2

hours

..........

Level 1

hours

..........

Approximate Exposure Time