TallyGenicom 3860 ユーザーガイド
3860/80 User’s Manual
E-2
Paper Out, Auto Load................................................. 10-7
Paper Path Change Failure, Recovering ..................... 10-6
Paper Paths, Changing from Control Panel ................ 10-5
Paper Paths, Changing from Host............................... 10-6
Paper Tension, Adjusting ........................................... 10-2
Paper, Non Bonded..................................................... 10-8
Parallel Data Cable ..................................................... 12-7
Parallel Interface......................................................... 12-5
Parallel Interface Signals ............................................ 12-5
Parallel Timing Diagram ............................................ 12-6
pedestal......................................................................... 2-1
power cord .................................................................... 2-1
Power Cords ................................................................. 2-2
power switch................................................................. 2-3
Power Up ...................................................................... 9-1
Paper Path Change Failure, Recovering ..................... 10-6
Paper Paths, Changing from Control Panel ................ 10-5
Paper Paths, Changing from Host............................... 10-6
Paper Tension, Adjusting ........................................... 10-2
Paper, Non Bonded..................................................... 10-8
Parallel Data Cable ..................................................... 12-7
Parallel Interface......................................................... 12-5
Parallel Interface Signals ............................................ 12-5
Parallel Timing Diagram ............................................ 12-6
pedestal......................................................................... 2-1
power cord .................................................................... 2-1
Power Cords ................................................................. 2-2
power switch................................................................. 2-3
Power Up ...................................................................... 9-1
Status ....................................................................... 9-1
Print Head Gap Adjustment........................................ 2-21
print nozzle ................................................................... 2-9
Print Reference ............................................................. 8-1
print nozzle ................................................................... 2-9
Print Reference ............................................................. 8-1
Left Print Reference.......................................... 8-2, 8-4
Local Margins .......................................................... 8-3
Negative Top of Form Adjust .................................. 8-3
Tear Off Distance..................................................... 8-2
Top Print Reference .......................................... 8-2, 8-3
Local Margins .......................................................... 8-3
Negative Top of Form Adjust .................................. 8-3
Tear Off Distance..................................................... 8-2
Top Print Reference .......................................... 8-2, 8-3
Printed Menu ................................................................ 4-1
> Arrow.................................................................... 4-1
Access the Printed Menu ......................................... 4-2
Entering Menu Values ............................................. 4-2
Exit......................................................................... 4-19
Former and First....................................................... 4-3
Margins for Menu Listings ...................................... 4-2
Access the Printed Menu ......................................... 4-2
Entering Menu Values ............................................. 4-2
Exit......................................................................... 4-19
Former and First....................................................... 4-3
Margins for Menu Listings ...................................... 4-2
Printed Menu Map ........................................................ 4-3
printer stand .................................................................. 2-1
Put Paper in the Tractors ............................................ 2-14
printer stand .................................................................. 2-1
Put Paper in the Tractors ............................................ 2-14
R
Rear Tractors, Removing............................................ 10-4
Removing the Ribbon................................................... 2-9
Reset ............................................................................. 9-1
ribbon advance knob..................................................... 2-8
ribbon cartridge ............................................................ 2-1
ribbon drive spindle ...................................................... 2-7
Removing the Ribbon................................................... 2-9
Reset ............................................................................. 9-1
ribbon advance knob..................................................... 2-8
ribbon cartridge ............................................................ 2-1
ribbon drive spindle ...................................................... 2-7
ribbon guide...................................................................2-9
rolling-ASCII pattern...................................................2-19
rolling-ASCII pattern...................................................2-19
S
Select the Emulation......................................................3-7
Serial Interface
Serial Interface
DOS Machines........................................................12-2
Parameters ..............................................................12-2
Seven or Eight Data Bits.........................................12-2
Transmitted Parity ..................................................12-3
Parameters ..............................................................12-2
Seven or Eight Data Bits.........................................12-2
Transmitted Parity ..................................................12-3
Serial Interface Data Cable..........................................12-3
Serial Interface Loopback Test....................................11-5
Serial Interface Pin Assignments.................................12-4
serial printer cables......................................................2-22
Software Options.......................................................... B-3
Software Options, Setting............................................. B-4
Software Upgrade..........................................................9-2
Sound emission..............................................................2-1
Specifications ............................................................... E-1
Status ...........................................................................2-23
Status Sheet ...................................................................3-9
Serial Interface Loopback Test....................................11-5
Serial Interface Pin Assignments.................................12-4
serial printer cables......................................................2-22
Software Options.......................................................... B-3
Software Options, Setting............................................. B-4
Software Upgrade..........................................................9-2
Sound emission..............................................................2-1
Specifications ............................................................... E-1
Status ...........................................................................2-23
Status Sheet ...................................................................3-9
T
Tear Off Distance ..........................................................8-2
Test Pattern..................................................................2-19
Top Margin....................................................................8-3
Top-of-Form................................................................2-21
tractor assembly.............................................................2-1
tractors.........................................................................2-10
Trouble Shooting
Test Pattern..................................................................2-19
Top Margin....................................................................8-3
Top-of-Form................................................................2-21
tractor assembly.............................................................2-1
tractors.........................................................................2-10
Trouble Shooting
Serial Interface Loopback Test ...............................11-5
Troubleshooting...........................................................11-1
Hex Dump...............................................................11-5
Troubleshooting Chart .................................. 11-3, 11-4
Troubleshooting Chart .................................. 11-3, 11-4
V
Various Keys .................................................................5-3
Vertical Alignment ........................................................8-1
Vertical Alignment ........................................................8-1
Vertical Paper Movement .........................................8-1