Cisco wvc210 クイック設定ガイド
Quick Start Guide
Cisco Small Business
Model WVC210 Wireless-G PTZ
Internet Video Camera with 2-Way Audio
Model WVC210 Wireless-G PTZ
Internet Video Camera with 2-Way Audio
Package Contents
•
WVC210 Camera
•
Power Adaptor
•
Antenna
•
Camera Desktop Stand
•
Quick Start Guide
•
6-Foot Ethernet Cable
•
Setup and Documentation CD-ROM
Before You Begin
•
To configure the Cisco WVC210 camera, you need at least one computer
with an active LAN IP connection.
with an active LAN IP connection.
•
You must perform the initial configuration of the Cisco WVC210 camera
from a personal computer connected to the camera using a wired
connection to the Ethernet port. The initial configuration cannot be
performed over a wireless connection.
from a personal computer connected to the camera using a wired
connection to the Ethernet port. The initial configuration cannot be
performed over a wireless connection.
Once the hardware installation is complete, Cisco strongly recommends that
you run the Setup Wizard on the Setup CD-ROM for first-time software
installation of the camera. Advanced users can set up the Cisco WVC210
directly from the web interface of the camera.
you run the Setup Wizard on the Setup CD-ROM for first-time software
installation of the camera. Advanced users can set up the Cisco WVC210
directly from the web interface of the camera.
Camera Installation
To install the Cisco WVC210 camera, follow these steps.
S
TEP
1
Connect the antenna to the antenna connector on the camera.
S
TEP
2
(Optional) The Cisco WVC210 camera includes a camera desktop
stand. Set the bottom of the camera into the stand.
stand. Set the bottom of the camera into the stand.
.
1
2
S
TEP
3
Place the camera, and adjust its aim accordingly.
S
TEP
4
Connect the included Ethernet network cable to the network router or
switch.
switch.
S
TEP
5
Connect the other end of the cable to the Cisco WVC210 camera’s
Ethernet port.
Ethernet port.
Network Switch,
or Router
PC connected
to Network
270797
Camera
Network Switch
or Router
270798
S
TEP
6
Connect the included power adapter to the camera's Power port. Plug
the other end into a standard electrical outlet.
the other end into a standard electrical outlet.
S
TEP
7
Verify that the camera LEDs are lit.
Refer to the following table that describes the LEDs and their functions.
Camera
Power
Outlet
270799
The Cisco WVC210 camera has four LEDs to let you know how the camera is
functioning.
functioning.
S
TEP
8
(Optional) If the Cisco WVC210 camera is not functioning correctly,
you can press the Reset button to reset the camera. The Reset button
is found next to the Ethernet port. Insert a paper clip into the opening
and hold it in for more than three seconds. Be aware that resetting the
camera will erase all of your settings and return the camera to factory
defaults.
you can press the Reset button to reset the camera. The Reset button
is found next to the Ethernet port. Insert a paper clip into the opening
and hold it in for more than three seconds. Be aware that resetting the
camera will erase all of your settings and return the camera to factory
defaults.
LED
Color
Description
Power
Amber
The POWER LED lights up when the camera is
powered on. It flashes for about 10-15 seconds while
the camera is initializing.
powered on. It flashes for about 10-15 seconds while
the camera is initializing.
Activity
Green
The ACTIVITY LED flashes when there is activity.
Ethernet
Green
The ETHERNET LED lights up when there is a
connection to a wired network. It flashes when data
is transmitted to or received from the wired network.
connection to a wired network. It flashes when data
is transmitted to or received from the wired network.
Wireless
Green
The WIRELESS LED lights up when there is a
connection to a wireless network. It flashes when
data is transmitted to or received from the wireless
network.
connection to a wireless network. It flashes when
data is transmitted to or received from the wireless
network.