Funkwerk Bintec WI-Client 5510000169 ユーザーズマニュアル

bintec WI-Client

WLAN Client for Industrial Applications; Part number 5510000169

Encryption WEP/WPA

WEP64 (40 bit key), WEP128 (104 bit key), WPA Personal, WPA Enterprise, WPA2 Personal,
WPA2 Enterprise

IEEE802.11i Authentication and
encryption

802.1x EAP-PEAP, 802.1x EAP-LEAP, 802.1x EAP-TLS, 802.1x EAP-TTLS

Automatic Rate Selection (ARS)

Avialable

Transmission speed

Automatic fall back or fixed transmission speed

Fixed bitrate

A fixed value for the transmission speed can be set

Data rates for 802.11b/g (2,4GHz)

54; 48; 36; 24; 18; 12; 9; 6 Mbps (OFDM modulation). 11; 5.5; 2; 1 Mbps (DSSS modulation)

Data rates for 802.11a/h (5GHz)

54; 48; 36; 24; 18; 12; 9; 6 Mbps (OFDM modulation)

Output power

Selectable 1, 3, 5, 10, 15, max. (18) dBm. The maximum output power varies according
datarate and frequency band.

Channel setting

According IEEE 802.11d

Antenna diversity

Can be switched on / off

Wireless mode

Infrastruce mode: For connection to Aps, i.e. W1002 or other AP’s. Ad-hoc mode: For
connection to other WI-Clients (Bridge)

802.11 modes

Compatibly modes: 802.11b only, 802.11g only, 802.11b/g mixed mode, 802.11a/h

AP Density

No roaming, high, middle, low. Select the accesspoint density to control the behaviour when
roaming between APs. The selected value defines the signal threshold where the device starts
scanning for other APs.

List of available AP’s

Include information about MAC address, SSID, Channel, Signal strenght

Country specific settings

Operation channel according the regulatory domain

TPC (Transmission power control)

At 5 GHz operation automatic power regulation supported according EN301893

DFS (Dynamic frequency selection)

Relevant for 5 GHz operation: Implementation is not mandatory for devices there working in
client mode. Together with bintec AP’s the maximum allowed EIRP in 5 GHz operation is 200
mW.

RTS/CTS

RTS/CTS Threshold selectable

Configuration and Setup

Via Webinterface

Supervision and Recovery

Supports the Compoint manager to detect the device on the LAN and mangaging the device
IP address. Reset Button to set the device back to defaults

Configuration Management

Via Configuration File up and download

Interface (mechanical)

RS232 Interface with 9-pole D-sub female connector

Interface (electrical)

300-115,2 kbit/s, RTS, CTS, DSR, DCD, RI

Operation

Data transmission parallel to the Ethernet communication

Handshake mode

XON/XOFF, RTS/CTS or DTR/DSR are local handshake modes. In 'remote mode' the status
of the handshake input signals (DSR+CTS) will be send to the remote side via an extra port.

Port Mode

TCP/IP server; TCP/IP client; UDP/IP; Printer server; Com Server. The TCP/IP server and
client mode is compatible to the implementation of the WIx040 and WIx065 Access Points.
The Com Server mode is compatible to some PC applications.

Funkwerk Enterprise Communications GmbH - Suedwestpark 94 - 90449 Nuremberg - Germany
Phone: +49 - (0)911 9673 0
Fax: +49 - (0)911 688 0725
E-Mail: info@funkwerk-ec.com - www.funkwerk-ec.com 

bintec WI-Client
11.03.2011
Subject to technical
alterations