Aten KH1508Ai DCP2977 クイック設定ガイド

Phillips head hex

M3 x 6

Phillips head hex

M3 x 6

Phillips head hex

M3 x 8

3

4

5-1

5-2

1. Port Selection Pushbuttons

2. Port LEDs

3. Reset Switch

4. Laptop USB Console Port

5. Firmware Upgrade Recovery Switch

6. Firmware Upgrade Port

7. Power LED

8. Station ID LED

1. Power Socket

2. Power Switch

3. LAN Port

4. PON Port

5. Daisy Chain Port

6. Grounding Terminal

7. Local Console Port Section

8. KVM Port Section

In a single stage installation, there are no additional KVM switches daisy chained down from the KH1508

Ai

 / 

KH1516

Ai

. To set up a single stage installation (the numbers in the diagram correspond with the numbers of the 

instruction steps), and do the following:

1. Ground the KH1508

Ai

 / KH1516

Ai

 by connecting one end of the grounding wire to the grounding terminal, and 

the other end of the wire to a suitable grounded object.

Note: Do not omit this step. Proper grounding helps to prevent damage to the unit from surges or static 

electricity.

2. Plug the console keyboard, monitor, and mouse into the unit’s console ports. The ports are color coded and 

marked with icons for easy identification.

Note: You can use any combination of keyboard and mouse connections. For example, you can use a PS/2 

keyboard with a USB mouse.

3. If you are using a laptop to control the KH1508Ai / KH1516Ai locally, use the Laptop USB Console Cable 

included in the package to connect the laptop to the KH1508Ai / KH1516Ai’s Laptop USB Console port, located 

on the unit’s front panel.

4. Use Cat 5e/6 cable to connect any available KVM port to a KVM adapter cable that is appropriate for the 

computer you are installing 

Note: To support a resolution of 1280x1024@75Hz, the recommended maximum distance between the unit and 

the KVM adapter cable is 50 meters; to support a resolution of 1600x1200@60Hz, the recommended 

maximum distance is 40 meters.

5. Connect the KVM adapter cable to the computer.

Plug the connectors on the KVM adapter cable into the appropriate ports of the computer you are installing.

6. Plug the LAN or WAN cable into the KH1508

Ai

 / KH1516

Ai

’s LAN port.

7. Plug the female end of the power cord into the KH1508

Ai

 / KH1516

Ai

's power socket; plug the male end into an 

AC power source.

After the KH1508

Ai

 / KH1516

Ai

 is cabled up, you can turn on the power. After it is powered up, you can turn on the 

servers.

The KH1508

Ai

 / KH1516

Ai

 can be mounted in a 19" (1U) racks. The mounting brackets can screw into either the 

front or the back of the unit so that it can attach to the front or the back of the rack. To rack mount the unit:

1. Remove the screws at the front or the rear, as shown in the diagram below.

2. Screw the mounting brackets into the sides of the unit at the front or the rear, as shown in the diagram below.

3. Slide the unit into the front or rear of the rack and secure it to the rack.

Note: The front and rear panel views are similar for the KH1508

Ai

, the difference being that the 

KH1508

Ai

 has only one row of LED lights (front) and one row of CPU ports (rear)

(KH1516

Ai

)

1

• For best results, we recommend that the computers used to access the KH1508

Ai

 / KH1516

Ai

 have 

at least a P III 1 GHz processor, and that their screen resolution is set to 1024 x 768

• For best results, we recommend an Internet connection speed of at least 128 kbps

• Browsers must support 128 bit data encryption

• To run the Windows client, you must have DirectX 8.0 or higher installed

• To run the Java client, you must have Sun’s JRE 6 update 3 or higher installed

• To run the Log Server, you must have the Microsoft Jet OLEDB 4.0 (or higher) driver installed

• A VGA, SVGA, or Multisync monitor capable of the highest resolution that you will be using on 

any computer in the installation.

• A USB or PS/2 style mouse

• A USB or PS/2 style keyboard

The following equipment must be installed on the computers that connect to the KH1508

Ai

 or 

KH1516

Ai

's KVM ports:

• A VGA, SVGA or Multisync port

• A Type A USB port and USB host controller (for USB KVM Adapter Cable Connection, see 

below)

• 6-pin mini-DIN keyboard and mouse ports (for PS/2 KVM Adapter Cable Connection, see below)

• Cat 5e/6 cable is required to connect the KH1508

Ai

 / KH1516

Ai

 to one of the KVM adapter cables.

• The following KVM adapter cables are required for use with the KH1508

Ai

 / KH1516

Ai

:

© Copyright 2012 ATEN

®

 International Co., Ltd.   www.aten.com

Altusen and the Altusen logo are trademarks of ATEN International Co., Ltd. 
All rights reserved. All other trademarks are the property of their respective owners.
This product is RoHS compliant    

2

Connect to devices with PS/2 ports  

KA7920 / KA7520 / KA7120 / KA9520 / KA9120 

Connect to devices with USB ports  

KA7970 / KA7570 / KA7170 / KA9570 / KA9170 

Connect to Sun Legacy systems (with 13W3 port)   KA9130 / KA7130 

Connect to Sun USB systems  

KA9170 / KA7170 

Connect to serial based devices  

KA9140 

(KH1516

Ai

)

All information, documentation, and specifications contained in this media are subject to change without prior notification by the manufacturer. 
Please visit our website to find the most up to date version. 

1 KH1508

Ai

 

or KH1516

Ai

 Cat 5 High-Density    

   KVM Over the NET™ Switch

1 Firmware Upgrade Cable

1 Laptop USB Console Cable

1 Power Cord

1 Rack Mount Kit

1 Foot Pad Set (4 pcs.)

1 User Instructions

Considering environmental protection, ATEN 

does not provide a fully printed user manual for 

this product. If the information contained in the 

Quick Start Guide is not enough for you to 

configure and operate your product, please visit 

our website www.aten.com, and download the 

full user manual.

Online Registration
• http://eservice.aten.com  

 
Technical Phone Support
International:
• 886-2-8692-6959
China:
• 86-10-5255-0110
Japan:
• 81-3-5615-5811
Korea:
• 82-2-467-6789
North America:
• 1-888-999-ATEN   Ext: 4988  
United Kingdom:
• 44-8-4481-58923