KitchenAid KVWB400DSS インストールガイド

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting 

installation. Read and follow the instructions provided 

with any tools listed here.

 

■

Level

 

■

Drill with 1

1

/

4

" (3.0 cm), 

3

/

8

" (9.5 mm), and 

5

/

16

" (7.9 mm) 

drill bits

 

■

Pencil

 

■

Wire stripper or utility knife

 

■

Tape measure or ruler

 

■

Pliers

 

■

Caulking gun and weatherproof caulking compound

 

■

Vent clamps

 

■

Jigsaw or keyhole saw

 

■

Flat-blade screwdriver

 

■

Metal snips

 

■

Phillips screwdriver

 

■

Metric hex key set

 

■

Home power supply cable

 

■

1

/

2

" (12.7 mm) UL Listed or CSA Approved strain relief

 

■

3 UL Listed wire connectors

 

■

1 wall or roof cap

 

■

Metal vent system

 

■

Recirculation Kit Part Number W1027063 for non-vented 

(recirculating) installations only. See the “Assistance or 

Service” section to order.

 

■

Charcoal Filter Kit part number W1027068 for non-vented 

(recirculating) installations only. See the “Assistance or 

Service” section to order.

 

■

6" (15.2 cm) diameter round metal vent duct - length required 

is determined by ceiling height.

Remove parts from packages. Check that all parts are included.

 

■

Hood canopy assembly with ventilator and light bulbs 

installed

 

■

Vent transition with back draft dampers installed

 

■

Metal grease filter(s)

 

■

Vent cover support bracket

 

■

Mounting template

 

■

2-piece vent cover

 

■

4 - 3.5 x 9.5 mm screws

 

■

4 - 3.5 x 6.5 mm screws

 

■

2 - 2.9 x 6.5 mm screws

 

■

6 - 5 x 45 mm mounting screws

 

■

2 - 8 x 40 mm wall anchors

 

■

4 - 10 x 60 mm wall anchors

 

■

4 - 5.4 x 75 mm screws (for 10 x 60 mm wall anchors)

 

■

Torx

®†  

T20

®†

 adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the 

installer’s responsibility to comply with installation clearances 

specified on the model/serial/rating plate. The model/serial/

rating plate is located inside the range hood on the rear wall 

of the range hood.
Canopy hood location should be away from strong draft areas, 

such as windows, doors, and strong heating vents.
Cabinet opening dimensions that are shown must be used. 

Given dimensions provide minimum clearance.
This range hood is recommended for use with cooktops with a 

maximum total rating of 65,000 BTUs or less.
Grounded electrical outlet is required. See the “Electrical 

Requirements” section.
The canopy hood is factory set for venting through the roof 

or wall. For non-vented (recirculating) Installation, see “For 

Non-vented (recirculating) Installations Only” in the “Connect 

Vent System” section. The Recirculation Kit Part Number is 

W1027063. Charcoal filters are also required for non-vented 

(recirculating) installations. The Charcoal Filter Kit Part Number is 

W1027068. See the “Assistance or Service” section to order. 
All openings in ceiling and wall where canopy hood will be 

installed must be sealed.

The installation of this range hood must conform to the 

Manufactured Home Construction Safety Standards, Title 24 

CFR, Part 328 (formerly the Federal Standard for Mobile Home 

Construction and Safety, Title 24, HUD, Part 280) or when 

such standard is not applicable, the standard for Manufactured 

Home Installation 1982 (Manufactured Home Sites, Communities 

and Setups) ANSI A225.1/NFPA 501A or latest edition, or with 

local codes.

†

®

TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.