Netgear M4300-48X (XSM4348CS) - Stackable Switches with Full PoE+ Provisioning ユーザーズマニュアル
Routing
316
M4200 and M4300 Series ProSAFE Managed Switches Web Management User Manual
Configure Address Resolution Protocol
The Address Resolution Protocol (ARP) associates a Layer 2 MAC address with a Layer 3
IPv4 address. The switch software features both dynamic and manual ARP configuration.
With manual ARP configuration, you can statically add entries into the ARP table.
IPv4 address. The switch software features both dynamic and manual ARP configuration.
With manual ARP configuration, you can statically add entries into the ARP table.
ARP is a necessary part of the Internet Protocol (IP) and is used to translate an IP address to
a media (MAC) address, defined by a local area network (LAN) such as Ethernet. A station
needing to send an IP packet must learn the MAC address of the IP destination, or of the next
hop router, if the destination is not on the same subnet. This is achieved by broadcasting an
needing to send an IP packet must learn the MAC address of the IP destination, or of the next
hop router, if the destination is not on the same subnet. This is achieved by broadcasting an
ARP request packet, to which the intended recipient responds by unicasting an ARP reply
containing its MAC address. Once learned, the MAC address is used in the destination
address field of the Layer 2 header prepended to the IP packet.
address field of the Layer 2 header prepended to the IP packet.
The ARP cache is a table maintained locally in each station on a network. ARP cache entries
are learned by examining the source information in the ARP packet payload fields, regardless
of whether it is an ARP request or response. Thus, when an ARP request is broadcast to all
stations on a LAN segment or virtual LAN (VLAN), each recipient has the opportunity to store
the sender’s IP and MAC address in its respective ARP cache. The ARP response, being
unicast, is normally seen only by the requestor, who stores the sender information in its ARP
cache. Newer information always replaces existing content in the ARP cache.
are learned by examining the source information in the ARP packet payload fields, regardless
of whether it is an ARP request or response. Thus, when an ARP request is broadcast to all
stations on a LAN segment or virtual LAN (VLAN), each recipient has the opportunity to store
the sender’s IP and MAC address in its respective ARP cache. The ARP response, being
unicast, is normally seen only by the requestor, who stores the sender information in its ARP
cache. Newer information always replaces existing content in the ARP cache.
The number of supported ARP entries is platform dependent.
Devices can be moved in a network, which means that the IP address that was at one time
associated with a certain MAC address is now found using a different MAC, or it disappeared
from the network altogether (for example, it was reconfigured, disconnected, or powered off).
This leads to stale information in the ARP cache unless entries are updated in reaction to
new information seen on the network, periodically refreshed to determine if an address still
exists, or removed from the cache if the entry was identified as a sender of an ARP packet
during the course of an ageout interval, usually specified through configuration.
associated with a certain MAC address is now found using a different MAC, or it disappeared
from the network altogether (for example, it was reconfigured, disconnected, or powered off).
This leads to stale information in the ARP cache unless entries are updated in reaction to
new information seen on the network, periodically refreshed to determine if an address still
exists, or removed from the cache if the entry was identified as a sender of an ARP packet
during the course of an ageout interval, usually specified through configuration.
Display the ARP Entries in the ARP Cache
Use this page to display ARP entries in the ARP cache. The table lists the remote
connections most recently seen by this switch.
connections most recently seen by this switch.
To display ARP entries in the ARP cache:
1.
Launch a web browser.
2.
Enter http://<ipaddress> in the web browser address field.
The login window opens.
3.
Enter the user name and password.
The default admin user name is admin and the default admin password is blank, that is,
do not enter a password.
do not enter a password.
4.
Click the Login button.