KitchenAid 1.4 cu. ft. Microwave 3.6 cu. ft. True Convection Lower Oven インストールガイド

Feed oven cable through opening in 
the cabinet. Make electrical connection

following the steps needed for your installation.

1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cable to junction box through the

U.L.-listed conduit connector. 

4. Connect the two black wires together with

twist-on connectors.

5. Connect the two red wires together with 

twist-on connectors. 

6. Complete electrical connection according to

local codes and ordinances.

7. Connect the factory-crimped bare

and white oven cable wires to
the neutral (white) wire in
junction box. See Figure 1.

8. Replace junction box cover.

7. Separate the factory-crimped

bare and white oven cable wires.

8. Connect white oven cable wire to

neutral (white) wire in junction
box. See Figure 2.

9. Connect the bare grounding

oven cable wire to a grounded
wire in the junction box. See
Figure 2.

10. Replace junction box cover.

7. Separate bare and white 

oven cable wires.

8. Connect white oven cable wire to

neutral (white) wire in junction
box.  See Figure 2.

9. Connect the bare grounding  oven

cable wire to the green grounding
wire in junction box. Do Not
connect bare grounding wire to
neutral (white) wire in junction
box. See Figure 2.

10. Replace junction box cover.

Lift oven into cabinet cutout using the

oven opening as an area to grip.

Push against seal area of front frame to push
oven into cabinet until shipping feet almost
contact cabinet. Use a Phillips screwdriver to
remove screws attaching shipping feet. Remove
and discard shipping feet.
Push oven completely into cabinet and center
oven in cabinet cutout.

Replace oven racks. 

oven. Press the “BROIL” pad. “BROIL” will
appear in the display. Press the “START” pad.

microwave oven.
• Fill a microwave-safe container with one cup of

water and place container inside microwave oven.
Close door firmly.

• Set microwave oven cook time to “2:00” 

minutes.

• Press the “START/ENTER” pad. The interior

microwave oven light should be on and the
remaining cooking time should be displayed.

Turn on power supply. The display

panel will light up briefly. “PF” should appear in
the temperature display.

Make sure the oven door is closed and the “ON”
light is shown in the display area. After 2 minutes,
partially open oven door. You should feel heat from
the oven. Press the “CANCEL” pad.
If your oven does not heat or an“F” appears in
the display, contact your dealer or check the “If
you need service...” section of this Installation
Instructions.

• When display reads “1:00,” open microwave

oven door. The microwave should stop cooking.

• Close door firmly. The interior microwave oven

light should turn off.

• Press the “START/ENTER” pad. Microwave oven

should begin cooking and the microwave oven
interior light should be on.

• Let microwave oven complete cooking time. A

tone will sound four times at end of cooking time
and microwave oven will shut off.

• Open microwave oven door and carefully remove

container. Water in container should be hot.

Important: Securely fasten oven to cabinet

using the screws provided (two screws for a single
oven or four screws for a double oven). Insert the
screws through holes in mounting rails. Do Not
overtighten screws.

Slide top end of each trim upward onto oven

side rails. Push each trim into place at bottom of
trim. Use screws to attach each trim to oven. Take
care not to scratch other surfaces with ends of trim.

If your house has aluminum wiring, see
“Electrical requirements”, Page 2.

Reinstall the oven door by inserting

ends of hinges into hinge slots in the oven
frame. Push  hinges in as far as they will go.
Open the door (you will feel the door drop
into place) and rotate both hinge latches back
to the locked position.

Close and open the door to check that the
door closes and opens completely. If door
does not close or open completely, repeat
the door removal step and reinstall door as
described above.