Honeywell HZ-7200 仕様ガイド

This EnergySmart® Cool Touch Heater is equipped with several devices and features for added protection:
-  This heater was crafted using a high quality safety plastic which allows for the “Cool Touch” exterior.  If the heater grille is 

touched briefly, it will not cause a burn.  For safe operation, do not continuously hold bare skin against the grille..

•  Tip over protection – a tip-over switch that disables the heater if it is accidentally tipped over.
•  A high temperature safety control prevents overheating.
•  Thermal cut-off fuse that will permanently shut down the heater should it operate at a higher than normal temperature.

It is recommended that the heater be cleaned at least once a month and before off-season storage.Save the carton for off-season storage.
•  Turn the heater OFF ( ) and unplug it. Allow it to cool.
•  Use a dry cloth to clean only the external surfaces of the heater.  DO NOT USE WATER, WAX, POLISH OR ANY CHEMICAL SOLUTION.
•  Before storing, clean the EnergySmart® Cool Touch Heater using the above-mentioned steps.  Wrap the cord around its cord wrap 

underneath the heater base. Pack the heater in its original carton and store it in a cool, dry place.

If your heater shuts off unexpectedly or fails to operate, one of your heater safety features may have been activated to prevent overheating.
•  Be sure it is plugged in and that the electrical outlet is working.
•  Check your EnergySmart® Thermostat setting.  The unit may simply be off because you have reached your desired heat setting.
•  Check for any obstructions.  If you find an obstruction, turn the heater OFF and unplug it.  Allow the heater to cool completely, 

then remove the obstruction.  Wait at least 10 minutes, then re-plug the heater in and follow the OPERATION instructions.

to use this product.
A.   This 3 year limited warranty applies to repair or 

replacement of product found to be defective in 

material or workmanship.  This warranty does not 

apply to damage resulting from commercial, abusive, 

unreasonable use or supplemental damage.  Defects 

that are the result of normal wear and tear will not be 

considered manufacturing defects under this warranty.  

OF THIS WARRANTY. Some jurisdictions do not allow 

the exclusion or limitation of incidental or consequential 

damages or limitations on how long an implied warranty 

lasts, so the above limitations or exclusions may not 

apply to you.  This warranty gives you specific legal rights, 

and you also may have other rights which vary from 

jurisdiction to jurisdiction.  This warranty applies only to 

the original purchaser of this product from the original 

date of purchase.

B.   At its option, Kaz USA, Inc. will repair or replace this 

product if it is found to be defective in material or 

workmanship.

C.   This warranty does not cover damage resulting from any 

unauthorized attempts to repair or from any use not in 

accordance with the instruction manual.

D.   Return defective product to Kaz USA, Inc.  with a brief 

description of the problem.  Include proof of purchase and 

a $10 US/$15.50 CAN check or money order for handling, 

return packing and shipping charges. Please include your 

name, address and a daytime phone number.  

 

You must prepay shipping charges. We suggest having 

tracking or delivery confirmation.  

Send to:

Kaz USA, Inc.   

Attn: Returns Department 

4755 Southpoint Drive 

Memphis, TN 38118  USA

Kaz Canada, Inc.  

Attn: Returns Department 

510 Bronte Street South 

Milton, ON L9T 2X6  Canada

Please go to www.kaz.com and register your product under 

the Customer Care Center and receive product information 

updates and new promotional offers.

Mail questions or comments to:
Kaz USA, Inc.  

Consumer Relations Dept. 

250 Turnpike Road 

Southborough, MA 01772

Call us toll-free at: 1-800-477-0457 

E-mail: consumerrelations@kaz.com
Or visit our website at: www.kaz.com
Please be sure to specify a model number.

Models 

HZ-7200/7300 Series 

HZ-8000 Series

Unit dims  10.4” L x 7” W x 11.7” H  8.7” L x 6.3” W x 18.1” H 
Amps 

12.5

Unit Voltage 

120V, 60Hz

Max Watts 

1500

Max BTUs 

5118

Operation Cost*  To estimate the cost to operate this heater, 

multiple the watts used times .001 to convert into a kilowatts 

measure and multiple by your local kilowatt electric rate for 

however long you run the heater. 

For example, if your electric rate is $.1196**per kilowatt hour 

and you ran this heater in constant high mode (1500 watts) for 

4 hours, it would cost you $.71 cents to run the heater (1500 

watts x 4 hours x.001) x .1196kwp = .71 cents)  
Note:  Because the Low Settings do not require as much 

electricity to operate, they are more energy efficient and may 

be better options if you are concerned about the amperage 

draw on a circuit when the heater is on the High (HI) setting.
*Calculation (Total Wattage x .001) x Cost per Kilowatt Hour = 

Cost to operate
**Average Retail Price of Electricity to Ultimate Customer by End-

Use, US Energy Information Administration, August 11, 2010

The Current Temp Indicator will display the current room 

temperature.   
In the EnergySmart® mode, the Energy Usage Indicator will display 

what power consumption the heater has automatically selected to 

efficiently meet your Desired Temperature.  
To override the EnergySmart® function, turn the heater OFF ( ) or 

press SET to choose a Constant Heat mode. 

EnergySmart™ Mode - A smart thermostat that helps you 

save energy.  Press SET to choose four (4) comfort settings of 

65°F (18°C), 70°F (21°C), 75°F (24°C), 80°F (27°C). This is 

NOTE: Because the Low setting does not require as much electricity 

to operate, it is more energy efficient and may be a better option if 

you are concerned about saving energy.

To set the heater, the digital control is equipped with two  

(2) modes: (See Fig. 2)
Constant Heat Mode - Choose from two (2) heat settings:
1.  Constant Low, press SET to LO; this setting uses 900 watts  

  of power
2.  Constant High, press SET to HI;  this setting uses 1500 watts  

  of power

your desired room temperature. The EnergySmart® thermostat 

will automatically select the appropriate power level to best 

accommodate your Desired Temperature. As the air temperature 

(Current Temp) in the room approaches the Desired Temperature, 

the heater will automatically lower the power consumption to 

provide consistent warmth without wasting energy.