Timberk SWH SE1 30 VO ユーザーズマニュアル
Water heater mounting
NOTE:
To install the water heater, please, use accessories provided by the
manufacturer. Electric water heater must not be mounted onto the wall
before you make sure that the mounting strip is installed firmly and
securely. Otherwise, the electric water heater may fall down from the
wall that may cause its damage and even more serious accidents
involving harm to health and personal injuries.
To install the water heater, please, use accessories provided by the
manufacturer. Electric water heater must not be mounted onto the wall
before you make sure that the mounting strip is installed firmly and
securely. Otherwise, the electric water heater may fall down from the
wall that may cause its damage and even more serious accidents
involving harm to health and personal injuries.
1. After you have chosen a proper place to install the water heater
determine points for holes for fixing of mounting strip, putting the strip
to a wall. Drill holes of corresponding depth in the wall using a drill
dimensionally fit for anchor bolts delivered together with the water
heater. Next, fix the mounting strip on a wall with help of screws. After
that you should mount water heater on a mounting strip (fig. 7).
2. Fasten an AC main socket to the wall. Requirements to the socket are
2. Fasten an AC main socket to the wall. Requirements to the socket are
as follows: 220V / 10 , single-phase, three wires. It is recommended to
place the socket from the right side higher of the water heater.
NOTE:
In the places accessible for water the AC electrical main socket must be
installed on a height of at least 1.8 m from the ground.
In the places accessible for water the AC electrical main socket must be
installed on a height of at least 1.8 m from the ground.
Fig. 7
Connection to the water main
1. The water heater must be connected to the water main with
minimum pressure of 0.1 MPa and maximum pressure of 0.7 MPa.
NOTE:
The water heater is the appliance operating in such a manner that
pressure of water in the water heater corresponds to the pressure of
water in the water main. If pressure in the water main exceeds 0.7 MPa
then it is necessary to install a pressure reducer before the water heater
so that pressure will not exceed 0.7 MPa.
The water heater is the appliance operating in such a manner that
pressure of water in the water heater corresponds to the pressure of
water in the water main. If pressure in the water main exceeds 0.7 MPa
then it is necessary to install a pressure reducer before the water heater
so that pressure will not exceed 0.7 MPa.
2. To connect the water heater to the water main apply pipes with
diameter of G1/2.
3. To prevent water leakage when connecting pipes use rubber sealing
3. To prevent water leakage when connecting pipes use rubber sealing
gaskets on the threaded pipe ends.
4. Screw the safety pressure valve onto the inlet nozzle marked with blue
4. Screw the safety pressure valve onto the inlet nozzle marked with blue
colour and an arrow pointed water flow direction so that the water flow
direction coincides with direction of the arrow on the valve case.
NOTE:
Do not install additional accessories, such as a cut-off valve, between
the safety pressure valve and inlet nozzle.
Do not install additional accessories, such as a cut-off valve, between
the safety pressure valve and inlet nozzle.
5. Water heater with the mounted valve must be connected to the water
main install a shut-off valve at the water inlet point. You need to connect
a drain pipe to the opening of the pressure relief of safety valve. Next you
should put a drain pipe to the sewer.
6. Connect a desired number of consumption points to the outlet nozzle
6. Connect a desired number of consumption points to the outlet nozzle
marked with red colour.
7. Check leak tightness of joints: open the cut-off valve and one of the
7. Check leak tightness of joints: open the cut-off valve and one of the
outlet valves. After the tank is filled with water, as evidenced by outflow of
water from the outlet valve, turn off the outlet valve and check leak
tightness of all the joints.
6
www.timberk.com electric storage water heater