Cisco Cisco 2600 3600 High Performance ATM Advanced Integration Module トラブルシューティングガイド
Why AIM?
With AIM−ATM or AIM−ATM−VOICE−30 module installed, you can install VWIC MFT cards in to those
slots. By configuring T1 controllers, you can make it to act like a regular ATM interface. Thus it can offer
ATM adaptation layer 2 (AAL2) and ATM adaptation layer 5 (AAL5) support for low−density T1/E1 data
and voice connections over ATM networks. AIM module allows service providers and enterprise customers to
take advantage of the reliability and quality of service (QoS) available with ATM connectivity.
slots. By configuring T1 controllers, you can make it to act like a regular ATM interface. Thus it can offer
ATM adaptation layer 2 (AAL2) and ATM adaptation layer 5 (AAL5) support for low−density T1/E1 data
and voice connections over ATM networks. AIM module allows service providers and enterprise customers to
take advantage of the reliability and quality of service (QoS) available with ATM connectivity.
The following is a sample configuration.
r06#conf t
Enter configuration commands, one per line. End with CNTL/Z.
r06(config)#controller t1 0/1
r06(config−controller)#mode atm
r06(config−controller)#end
r06#sh int atm0/1
ATM0/1 is up, line protocol is down
Hardware is ATM T1
MTU 4470 bytes, sub MTU 4470, BW 1536 Kbit, DLY 20000 usec,
reliability 0/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5
255 maximum active VCs, 256 VCs per VP, 0 current VCCs
VC idle disconnect time: 300 seconds
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 1152 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
r06#
By default, AIM−ATM or AIM−ATM−VOICE−30 modules support 5 bits for VPI ( 0−31 ) and 8 bits for
VCI (0−255 ). However, VPI and VCI can be altered as required using the command atm vc−per−vp
under the ATM interface.
VCI (0−255 ). However, VPI and VCI can be altered as required using the command atm vc−per−vp
under the ATM interface.
Related Information
Advanced Integration Module Installation in Cisco 2600 Series, Cisco 3600 Series, and Cisco
3700 Series Routers Quick Start Guide
3700 Series Routers Quick Start Guide
•
AIM−ATM, AIM−VOICE−30, and AIM−ATM−VOICE−30 modules
•
Voice/Fax and ATM AIM Modules for the Cisco 2600, 3660 and Cisco 3700 Series Modular
Multiservice Access Routers Data Sheet
Multiservice Access Routers Data Sheet
•
Technical Support − Cisco Systems
•
More ATM Information
•
Contacts & Feedback | Help | Site Map