Cisco Cisco TelePresence MX700 インストールガイド

Configuring IP

(When not set by a provisioning system)

Your video conference system supports IP version 4 (IPv4), IP 

version 6 (IPv6) and Dual, which is the default setting. In all 

three cases, the IP parameters can be assigned automatically 

by the network, or you can set everything manually. When set 

to Dual, the network interface can operate on both IP versions, 

and have both an IPv4 and an IPv6 address. 

If you wish to set the parameters manually, contact your network 

administrator to obtain the required parameters.

If you choose to set the IP settings manually while using the 

Dual mode, you have to set both the IPv4 and the IPv6 settings. 

Start from point 2 in the instructions. 

If an IP address is already assigned to your system, you find the 

current IPv4 and/or IPv6 address on the System Information 

page: Go to 

.

The IPv4 Address and/or IPv6 Address of the system is shown 

in the 

section on the System Information page.

Press

 (the right most function key) to exit.

NOTE:

 You must restart the system after changing the IP 

settings for the changes to take effect.

To set or change the IPv4 settings

1. 

Select IP version 

Go to 

. Go to 

 and select 

.

 

2. 

Select automatic or manual IP assignment

Go to 

. Select 

, if you want automatic 

IP assignment; select 

, if you want to set the IP 

address manually.

a.  If you selected 

, the IP configuration is complete.

b.  If you selected 

, go to 

 and enter the 

, 

, and 

. Go to the 

 section and enter the DNS server address in the 

 input field. 

3. 

Press 

Home

 

(   )

 to return to the home menu.

To set or change the IPv6 settings

1. 

Select IP version 

Go to 

. Go to 

 and select 

 

2. 

Select automatic or manual IP assignment

Go to 

. Select 

 in the 

, if you want automatic IP assignment; select 

, 

if you want to set the IP address manually; or 

.*

a.  If you selected 

, go to 

Set to 

On or Off according to your preference.**

b.  If you selected 

, go to 

 and enter the 

IP address. Go to 

, and enter the gateway 

address. Set 

 to 

On or Off according 

to your preference.** 

3. 

Set DNS and NTP server addresses

If DHCP Options are switched off, you must set the DNS 

and NTP server addresses in 

. Go to the 

 section and enter the DNS 

server address in the 

 input field.

To set the NTP address, go to 

 

and set the address. Select 

 to confirm the address.

Set 

 to 

.

4. 

Press 

Home

 

(   )

 to return to the home menu.

Always save the new value when you change a setting

•  Drop down list selection: Navigate to the correct value 

and press the 

( )

 key to save, or press the left 

arrow key   to leave without saving.

•  Text entry in an input field: Enter the text, navigate to 

 to save the change, or navigate to 

 

to leave without saving; then press the 

 

( ) key 

to 

confirm.

Back to task overview

*) IP assignment: 

DHCPv6: All IPv6 addresses, including options, are obtained automatically 

from a DHCPv6 server. 

Autoconf: The system and gateway IP addresses will be assigned 

automatically. The options, e.g. NTP and DNS server addresses, must be 

set/assigned according to the DHCP Options setting. ** 

Static: The system and gateway IP addresses must be configured manually. 

The options, e.g. NTP and DNS server addresses, must be set/assigned 

according to the DHCP Options setting. **

**) DHCP options: 

On: The IP parameters, like the DNS and NTP server addresses, will be 

obtained automatically from a DHCPv6 server. 

Off: The IP parameters, like the DNS and NTP server addresses, must be 

set manually.

Cisco TelePresence Video Systems

D14639.10 Video Systems Getting Started Guide TC6.2, July 2013. 

Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved. 

19

Getting Started Guide

Contents

Introduction

User interfaces

Configuration

Appendices

Contacts

Confirguration