Cisco Cisco Nexus 1010 Virtual Services Appliance トラブルシューティングガイド
S e n d d o c u m e n t c o m m e n t s t o n e x u s 1 k - d o c f e e d b a c k @ c i s c o . c o m .
4
Cisco Nexus Virtual Services Appliance Troubleshooting Guide, Release 4.2(1)SP1(5.1)
OL-27731-01
Problems with Cisco Nexus Virtual Services Appliance
Problems with Cisco Nexus Virtual Services Appliance
This section includes symptoms, possible causes and solutions for the following problems with Cisco
Nexus Virtual Services Appliance product family..
Nexus Virtual Services Appliance product family..
Table 1-1
Problems with Cisco Nexus Virtual Services Appliance Product Family
Symptom
Possible Causes
Verification and Solution
The output of the show system
redundancy status command,
displays the standby Cisco Nexus
Virtual Services Appliance in warm
standby state.
redundancy status command,
displays the standby Cisco Nexus
Virtual Services Appliance in warm
standby state.
This may occur when there is no
control traffic communication
between the Cisco Nexus Virtual
Services Appliance HA pair.
control traffic communication
between the Cisco Nexus Virtual
Services Appliance HA pair.
1.
Verify if the control VLAN configuration of
both primary and secondary Cisco Nexus
Virtual Services Appliance is the same.
both primary and secondary Cisco Nexus
Virtual Services Appliance is the same.
show svs domain
2.
Verify if the upstream switch for both
primary and secondary Cisco Nexus Virtual
Services Appliance is configured by
allowing the control VLAN in the list of
VLAN permitted in the upstream trunk port.
primary and secondary Cisco Nexus Virtual
Services Appliance is configured by
allowing the control VLAN in the list of
VLAN permitted in the upstream trunk port.
interface name
switchport trunk allowed vlan add id
3.
Verify the status of the ports.
show network uplink
The output of the show
virtual-service-blade summary
command displays the status of the
VSB on the active Cisco Nexus
Virtual Services Appliance as power
in progress and the status of the VSB
on the standby Cisco Nexus Virtual
Services Appliance as powered on.
virtual-service-blade summary
command displays the status of the
VSB on the active Cisco Nexus
Virtual Services Appliance as power
in progress and the status of the VSB
on the standby Cisco Nexus Virtual
Services Appliance as powered on.
This may occur after the reload or
upgrade of Cisco Nexus Virtual
Services Appliance.
upgrade of Cisco Nexus Virtual
Services Appliance.
1.
Manually sync the state of the VSB on the
Cisco Nexus Virtual Services Appliance.
Enter the command in the virtual service
blade configuration mode.
Cisco Nexus Virtual Services Appliance.
Enter the command in the virtual service
blade configuration mode.
description " "
2.
Verify the status of the VSB.
show virtual-service-blade summary
Removal of a VSB fails and the
following error message is logged:
following error message is logged:
Previous command in progress
Multiple operations were carried
out on the VSB before it was
removed.
out on the VSB before it was
removed.
1.
Manually remove the VSB using the
following command:
following command:
no enable force
2.
Verify the removal of the VSB.
show virtual-service-blade summary
Cisco Nexus Virtual Services
Appliance reboots continuously and
the following error message is
logged:
Appliance reboots continuously and
the following error message is
logged:
Failed To boot server
In the flexible network uplink
types, invalid network uplink types
were assigned to Cisco Nexus
Virtual Services Appliance.
types, invalid network uplink types
were assigned to Cisco Nexus
Virtual Services Appliance.
Ensure that only valid uplinks are assigned to
Cisco Nexus Virtual Services Appliance.
Cisco Nexus Virtual Services Appliance.
See the Cisco Nexus Virtual Services Appliance
Software Configuration Guide, Release
4.2(1)SP1(5.1) for valid uplink types.
Software Configuration Guide, Release
4.2(1)SP1(5.1) for valid uplink types.