Cisco Cisco 1 GHz GainMaker Amplifier データシート
Data Sheet
Page 7 of 8
Ordering Information
The GainMaker Ordering Matrix provides ordering information for configured amplifier modules or
stations. This page contains ordering information for required and optional accessories that are not
included as part of a configured amplifier module or station. Please consult with your Account
Representative, Customer Service Representative, or Applications Engineer to determine the best
configuration for your particular application.
Table 7.
Required Accessories - must be ordered separately (not included via GainMaker Ordering Matrix)
Required Accessories
Part Number
Plug-in Pads (attenuators) - Available in 0.5 dB steps from 0 to 20 dB
● 1 required for forward input
● 1 required for AGC, if applicable*
● 4 required for reverse (3 input, 1 output)
● 1 required for AGC, if applicable*
● 4 required for reverse (3 input, 1 output)
* To determine AGC pad value, subtract 34 dB from the design value main port RF
output level at the AGC pilot frequency (applies to HGD, LGD, HGBT only)
output level at the AGC pilot frequency (applies to HGD, LGD, HGBT only)
589693 (0 dB) sequentially
thru 589734 (20.5 dB)
thru 589734 (20.5 dB)
Plug-in Forward Equalizer - Available in 1.5 dB steps from 0 to 30 dB at 1002 MHz
● 1 required for forward input
4007228 (0 dB) sequentially
thru 4007248 (30 dB)
thru 4007248 (30 dB)
Plug-in Reverse Equalizer - Available in 1 dB steps from 0 to 12 dB at 65 MHz
● 1 required for reverse output – unless design value is 0 dB (0 dB EQ is provided)
712719 (0 dB) and 589736
(1 dB) sequentially thru
589747 (12 dB)
(1 dB) sequentially thru
589747 (12 dB)
Table 8.
Optional Accessories (may be ordered separately)
Optional Accessories
Part Number
24 V Power Supply for GainMaker High Output HGD
4026157
230 V AC Crowbar Surge Protector (plug-in, one per station)
715973
Plug-in Inverse Equalizer. Simulates cable equivalent tilts (creates tilt opposite
that of equalizers). Use in place of forward input EQ as needed to maintain
proper output tilt in short spaced locations. Available in 1.6
that of equalizers). Use in place of forward input EQ as needed to maintain
proper output tilt in short spaced locations. Available in 1.6
dB “cable equivalent”
steps from 1.6 to 16.2 dB.
4007486 (1.6 dB) sequentially thru
4007495 (16.2 dB)
4007495 (16.2 dB)
Long Reach Test Point Adapter
562580
Status Monitoring Transponder
*
*See Transponder for GainMaker Optoelectronic Node data sheet, part number 7000087.
Table 9.
Housing Options
– The following Housing Options may be included with the product if ordered
using the GainMaker Ordering Matrix. They may also be ordered separately.
GainMaker System Amplifier Housing
– One required. Housing includes housing base, lid,
wiring harness, and 24 V power supply, part number 4022846. All housings have 15 A capacity.
Part Number
Uncoated 4 port housing without external test point access
714027
Chromate Plated 4 port housing without external test point access
714026
Uncoated 4 port housing with external test point access
714025
Chromate Plated 4 port housing without external test point access
714024
GainMaker System Amplifier Housing Upgrade Kit
– One required if upgrading an existing SA II,
II+, or III housing to allow use of GainMaker System Amplifier modules. Includes a GainMaker
System Amplifier housing lid, wiring harness, and 24 V power supply, part number 4022846.
System Amplifier housing lid, wiring harness, and 24 V power supply, part number 4022846.
II+, or III housing to allow use of GainMaker System Amplifier modules. Includes a GainMaker
System Amplifier housing lid, wiring harness, and 24 V power supply # 589420.
System Amplifier housing lid, wiring harness, and 24 V power supply # 589420.
Uncoated 4 port housing lid without external test point access
714023
Painted 4 port housing lid without external test point access
714022
Uncoated 4 port housing lid with external test point access
714021
Painted 4 port housing lid with external test point access
714020
Seizure Upgrade Kit
– 1 required if upgrading an existing SA II or SA II+ housing base to allow
use of GainMaker System Amplifier Modules. Includes high current (15 amp) rated seizure
screws and anvils.
screws and anvils.
548775