Samsung SNT-1010P ユーザーズマニュアル
23
Chapter 3 Network Connection &Setup
To Connect SNT-1010 to an IP sharer with the xDSL/Cable modem
22
1
Launch an Internet browser on the local PC
connected to the IP Sharer.
connected to the IP Sharer.
2
Enter the IP Sharer’s address in the
address bar of the browser.
address bar of the browser.
ex) http://192.168.1.1 ,http://192.168.0.1 or
http://192.168.xxx.1
For the address of the IP sharer, refer to the
product’s documentation.
3
When the IP Sharer is connected, the login
window appears and prompts you to enter
the password.
window appears and prompts you to enter
the password.
For the login IP and the password, refer to the
IP sharer’s documentation.
4
When done, you will see the setup window
of the IP sharer. In the setup menu, select
“Automatic Configuration-DHCP ” for
Internet Connection Type.
of the IP sharer. In the setup menu, select
“Automatic Configuration-DHCP ” for
Internet Connection Type.
For the menu location of Internet Connection
Type and DHCP, refer to the IP sharer’s
documentation.
5
Some Internet service providers may
require additional information such as user
ID, password or host name for the
connection using DHCP. For more
information, contact your Internet service
provider.
require additional information such as user
ID, password or host name for the
connection using DHCP. For more
information, contact your Internet service
provider.
6
When done, click the <Save> or <Apply>
button to save the settings.
button to save the settings.
4
B. If the IP sharer is connected to an xDSL modem using DHCP
Network Connection & Setup
To Connect SNT-1010 to an IP sharer with the xDSL/Cable modem
(Continued)
[STEP 3 ] To check if the IP sharer is connected to the xDSL /Cable modem properly
[STEP 4 ] To connect SNT-1010 to the IP sharer
Select <Status> from the Settings menu of the IP Sharer
A. If using Dynamic IP mode of SNT-1010
B. If using Static IP mode of SNT-1010
If it is properly connected, <IP Address>, <Subnet Mask> and <Gateway> provided by your
ISP are displayed. Please remember these values because they are required so that an
external remote computer of the IP sharer connects to SNT-1010. However, note that certain
ISPs change the settings of <IP Address>, <Subnet Mask>and <Gateway>on a regular basis
If the IP sharer is not properly connected, press the <Connect> button to try to reconnect or
check if the settings of the IP sharer are correct.
1. Position the IP selection switch to D (Dynamic IP).
2. SNT-1010 is connected to the IP sharer using the Direct LAN
2. SNT-1010 is connected to the IP sharer using the Direct LAN
Cable (UTP cable).
SNT-1010 does not come with the Direct LAN cable.
You have to purchase it separately.
You have to purchase it separately.
3. Connect SNT-1010 to the power source.
4. When SNT-1010 starts, it automatically obtains an IP address from
4. When SNT-1010 starts, it automatically obtains an IP address from
the IP sharer.
5. You can check the dynamic IP address from the IP sharer by using
the IP installer on your PC.
For how to use the IP installer, refer to “Dynamic IP Setting:
Check Dynamic IP” on page 38.
Check Dynamic IP” on page 38.
1. Position the IP selection switch to S (Static IP).
2. SNT-1010 is connected to the IP sharer using the Direct LAN
2. SNT-1010 is connected to the IP sharer using the Direct LAN
Cable (UTP cable).
SNT-1010 does not come with the Direct LAN cable.
You have to purchase it separately.
You have to purchase it separately.
3. Connect SNT-1010 to the power source.
4. Use the IP installer on your local PC to configure the
4. Use the IP installer on your local PC to configure the
<IP address>, <Subnet Mask>, <Gateway>and <Port>settings.
For how to use the IP installer, refer to “Static IP Setting” on
page 33.
page 33.