Samsung SNT-1010P ユーザーズマニュアル

Chapter 8 Setting Up

Basic Configuration

<IP Type> : Shows the current SNT-1010 IP setting type.

- To change the IP setting type, slide the [IP select switch] on the front panel to <D> or <S> position according to your needs.

<IP Configuration> : Allows setting SNT-1010 IP and port related settings.

- <MAC Address> : Shows the Ethernet MAC address. Since this value is used to create a DDNS address, confirm the value.

- <IP Address> : Shows the currently configured IP address. If the <IP Type> is set to <Static IP>, you can change the IP address.

- <Subnet Mask> : Shows the <Subnet Mask> for the configured IP address.

- <Gateway> : Shows the <Gateway> address for the configured IP address.

- <DNS Server> : Shows the IP address of the DNS (Domain Name Service) server.

- <HTTP Webserver Port> : Shows the HTTP port used to connect to the SNT-1010 using the web browser.The default port number is 80(TCP).

- <Device Port(TCP)> : A port used to control video transmission. The default value is 60001(TCP).

- <TCP Streaming Port> : A port used to transfer video using the TCP protocols. The default value is 60002(TCP).

- <UDP Streaming Port> : A port used to transfer video using the UDP multicast protocols. The default value is 60003(UDP).

- <Upload Port(TCP)> : A port used to upgrade software. Default value is 60004(TCP).

<Multicast Settings> : To transmit a video using UDP Multicast, you can set the IP address, port and TTL.

- <Multicast Address> : Shows IP address set for video transmission using UDP Multicast.

The default value is 239.0.0.1. It is recommended to set it to between 224.0.0.0 and 239.255.255.255.

- <Multicast Port> : Shows UDP port set for video transmission using UDP Multicast. The default value is 60005(UDP).

- <TTL> : TTL stands for “Time To Live” that allows you to set the number of routers so that the packet can pass through.

Each router decrease the TTL value one by one when a packet passes it through. If the TTL value reaches 0, the packet cannot pass
through a router. The default value is 63. It is recommended to set it to between 0 and 255.

To setup IP settings

If more than an SNT-1010 are
connected to an IP Sharer, set the IP
and port Settings for SNT-1010’s
differently.

35 Page

Note

You can set the video format, size, resolution, frames per second for <Video1> and <Video2>.

<Video Format> : Select a video format from <MPEG4> and <MJPEG>.

- To transmit a video when an event occurs, either <Video1> or <Video2> must be set to <MJPEG>.

- To use the motion detection function, either <Video1> or <Video2> must be set to <MPEG4>.

Example) To set <Video1> for the motion detection and to send a video from <Video2> to an e-mail or FTP when an
event occurs, set the <Video1> to <MPEG4> and the <Video2> to <MJPEG>.

<Resolution> : Select a video size among from <D1>, <VGA>, <CIF> and <QCIF>.

- <D1>: 720 x 480 (NTSC), 720 x 576 (PAL)

- <VGA> : 640 x 480

- <CIF> : 360 x 240(NTSC), 360 x 288 (PAL)

- <QCIF> : 176 x 112(NTSC), 176 x 144 (PAL)

<Quality>: Select a resolution from <Very High>, <High>, <Normal>, <Low> and <Very Low>.

<Frame Rate(Max)> : Shows the maximum number of frames per second depending on the

Bandwidth configured in <NETWORK>

<STREAMING SETUP>

<Streaming Control>. If it is set to <Unlimited>, you can select one from
<30 fps>, <15 fps>, <7.5 fps>, <3 fps> and <1 fps>.

Click <BASIC CONFIGURATION>

<VIDEO>.

The VIDEO CONFIGURATION window
appears.

Setting Video

To complete the video setting,
click the [Apply] button.

The settings are saved.

Click <BASIC CONFIGURATION>

<IP>.

IP Setting window appears.

To complete the setting, click the

[Apply] button.

The settings are saved and the system is restarted.

The currently opened web browser is closed.

Basic Configuration

Setting Up