Samsung ED32D クイック設定ガイド
Quick Setup Guide
ED32D ED40D ED46D ED55D
BN68-05831S-00
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
Reverse Side
Issues
Solutions
The screen keeps
switching on and off.
switching on and off.
Check the cable connection between the
product and PC, and ensure the connection is
secure.
product and PC, and ensure the connection is
secure.
No Signal is displayed
on the screen.
on the screen.
Check that the product is connected correctly
with a cable.
Check that the device connected to the
product is powered on.
with a cable.
Check that the device connected to the
product is powered on.
Not Optimum Mode is
displayed.
displayed.
This message is displayed when a signal
from the graphics card exceeds the product’s
maximum resolution and frequency.
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
from the graphics card exceeds the product’s
maximum resolution and frequency.
Refer to the Standard Signal Mode Table and
set the maximum resolution and frequency
according to the product specifications.
The images on the
screen look distorted.
screen look distorted.
Check the cable connection to the product.
The screen is not clear.
The screen is blurry.
The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
recommended level.
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
recommended level.
The screen appears
unstable and shaky.
unstable and shaky.
Check that the resolution and frequency of the
PC and graphics card are set within a range
compatible with the product. Then, change the
screen settings if required by referring to the
Additional Information on the product menu
and the Standard Signal Mode Table.
PC and graphics card are set within a range
compatible with the product. Then, change the
screen settings if required by referring to the
Additional Information on the product menu
and the Standard Signal Mode Table.
There are shadows or
ghost images left on the
screen.
ghost images left on the
screen.
Issues
Solutions
The screen is too bright.
The screen is too dark.
The screen is too dark.
Adjust Brightness and Contrast.
Screen colour is
inconsistent.
inconsistent.
Go to Picture and adjust the Colour Space
settings.
settings.
White does not really
look white.
look white.
Go to Picture and adjust the White Balance
settings.
settings.
There is no sound.
Check the connection of the audio cable or
adjust the volume.
adjust the volume.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to
the maximum level, adjust the volume on
your PC sound card or software programme.
the maximum level, adjust the volume on
your PC sound card or software programme.
The remote control does
not work.
not work.
Make sure that the batteries are correctly in
place (+/-).
place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs
switched on in the vicinity.
switched on in the vicinity.
Port
Description
HDMI IN
Connects to a source device using an HDMI cable.
SERVICE (5V 0.5A)
This port is used to upgrade the software.
RGB IN
Connects to a source device using a D-SUB cable.
DVI IN
Connects to a source device using a DVI cable or HDMI-DVI cable.
AUDIO OUT
Connects to the audio of a source device.
RGB / DVI / HDMI / AV /
COMPONENT AUDIO IN
COMPONENT AUDIO IN
Connect to audio input using an audio cable.
RS232C IN
Connects to MDC using an RS232C-stereo adapter.
- For details on how to use the MDC programme, refer to Help after installing the programme. The MDC programme is available
- For details on how to use the MDC programme, refer to Help after installing the programme. The MDC programme is available
on the website.
RS232C OUT
COMPONENT / AV IN
Connects to a source device using the Component/AV cable.
Remote Sensor
To control the remote control in front of the product, lower the remote control sensor in the direction of the arrow.
Troubleshooting Guide
Checking the Components
Remote Control
- Contact the vendor where you purchased the product if any
components are missing.
- The appearance of the components may differ from the images
shown.
Quick Setup Guide
Warranty card
(Not available in some locations)
D-SUB cable
Power cord
+
+
-
-
Remote Control
Batteries
(Not available in some locations)
RS232C(IN) adapter
Remote Sensor
- The colour and the appearance may differ depending on the product, and the specifications
are subject to change without prior notice to improve the performance.
- Recommended hours of use per day of this product is under 16 hours.
If the product is used for longer than 16 hours a day, the warranty may be void.
- Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
1
2
3
4
1
Display or hide the onscreen display menu, or return to the
previous menu.
previous menu.
2
Move to the upper, lower, left or right menu, or adjust an option's
setting.
setting.
3
Confirm a menu selection.
4
Exit the current menu.
EDD32~55-India-QSG_BN68-05831S-00.indd 1
2015-11-27 4:32:59